Home › Engine / Hybrid System › 3ZR-FAE (ENGINE CONTROL) › CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER
RM32H0E _51 Engine / Hybrid System _059607 3ZR-FAE ENGINE CONTROL _0293870 CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER A

3ZR-FAE ENGINE CONTROL  CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER  INSTALLATION  


PROCEDURE

Hide 222A0 1.INSTALL CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the continuously variable valve lift controller assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A207933C03
2.854,1.292 3.26,0.302 3.26,0.302 2.99,0.302 false 2.813,0.208 3.135,0.406 0.323,0.198 10 false *1 2.427,2.521 2.74,2.677 0.313,0.156 10 false *a
*1 Valve Lift Control Actuator Connector
*a Protrusion length


Measure the protrusion length of the continuously variable valve lift controller assembly.

Standard Protrusion Length:

34.57 to 34.73 mm (1.36 to 1.37 in.)


HINT:
·

When reinstalling the continuously variable valve lift controller assembly, perform the measurement after the valve lift control actuator connector is installed.

·

It is not necessary to perform this measurement when installing a new continuously variable valve lift controller assembly as the protrusion length is 34.57 to 34.73 mm (1.36 to 1.37 in.).

·

If the protrusion length of the continuously variable valve lift controller assembly is not 34.57 to 34.73 mm (1.36 to 1.37 in.), perform the Active Test and adjust the protrusion length to the specified value.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER>ON-VEHICLE INSPECTION




b.
A320670C05
2,1 2.417,0.427 2.417,0.427 2.583,0.427 false 1.479,1.417 0.75,0.813 0.75,0.813 0.552,0.813 false 2.625,0.365 2.969,0.604 0.344,0.24 10 false *1 0.406,0.74 0.75,0.979 0.344,0.24 10 false *a
*1 O-ring
*a Protrusion


Install a new O-ring to the continuously variable valve lift controller assembly.

NOTICE:
·

Align the protrusion of the O-ring with the protrusion of the continuously variable valve lift controller assembly.

·

Make sure that the O-ring is not protruding from the groove in the continuously variable valve lift controller assembly.




c.
A173948

Rotate the crankshaft clockwise to retract the valve rocker shaft assembly.


d.
A319440C01
0.573,2.344 0.938,2.646 0.365,0.302 10 false *a 1.354,0.198 1.719,0.5 0.365,0.302 10 false *b
*a No. 1 Cylinder
*b No. 3 Cylinder


Rotate the crankshaft clockwise again until the intake camshaft position at the No. 1 cylinder and No. 3 cylinder are as shown in the illustration.


e.
A173632

Install the valve lift control actuator connector clip to the valve lift control actuator connector.

NOTICE:

Be sure to insert the protrusions of the valve lift control actuator connector clip into the holes in the valve lift control actuator connector.


HINT:

A new continuously variable valve lift controller assembly is supplied with the valve lift control actuator connector installed. Make sure to remove the valve lift control actuator connector before installation.



f.
A299868

Install the valve lift control actuator connector to the valve rocker shaft assembly.


g.

Insert the continuously variable valve lift controller assembly into the camshaft housing sub-assembly.


h.

Install the continuously variable valve lift controller assembly to the camshaft housing sub-assembly with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:
·

Make sure the O-ring is not caught between the parts.

·

If the continuously variable valve lift controller assembly has been struck or dropped, replace it.




i.

Install the wire harness clamp bracket to the camshaft housing sub-assembly with the 2 nuts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


j.

Using a screwdriver, slide the valve lift control actuator connector clip from the valve lift control actuator connector.

NOTICE:

Slide only the upper part of the valve lift control actuator connector clip, as the straight pin will fall out from the bottom if the valve lift control actuator connector clip is completely removed.



k.
A319442

Using 2 screwdrivers, lightly pry the valve lift control actuator connector and align the hole in the valve lift control actuator connector with the hole in the continuously variable valve lift controller assembly.

NOTICE:
·

Do not forcibly pry the valve lift control actuator connector.

·

Do not damage the camshaft housing sub-assembly or camshaft bearing cap.




l.
A320531C01
1.125,4.052 1.26,4.052 1.26,4.052 1.365,3.802 false 1.542,3.031 1.333,2.76 1.333,2.76 1.156,2.76 false 2.156,4.24 1.969,4.24 1.969,4.24 1.771,3.938 false 0.583,3.469 1.167,3.469 false 1.781,3.167 1.781,2.74 1.781,2.74 1.969,2.74 false 2.25,3.469 2.833,3.469 false 2.875,3.396 3.156,3.625 0.281,0.229 10 false *1 0.969,3.979 1.25,4.208 0.281,0.229 10 false *2 1,2.698 1.281,2.927 0.281,0.229 10 false *3 2.177,4.177 2.458,4.406 0.281,0.229 10 false *3 0.427,3.396 0.708,3.625 0.281,0.229 10 false *4 2.01,2.667 2.292,2.896 0.281,0.229 10 false *5
*1 Continuously Variable Valve Lift Controller Assembly
*2 Valve Lift Control Actuator Connector
*3 Valve Lift Control Actuator Connector Clip
*4 Valve Rocker Shaft Assembly
*5 Straight Pin


Insert the straight pin into the valve lift control actuator connector.

NOTICE:

Do not use a tool to insert the straight pin. Insert the straight pin by hand.


HINT:

If the straight pin is difficult to insert, insert the straight pin while lightly prying the valve lift control actuator connector.



m.

Using a screwdriver, install the valve lift control actuator connector clip to the valve lift control actuator connector.

NOTICE:

Insert the protrusion of the valve lift control actuator connector clip into the hole in the valve lift control actuator connector.



Hide 11213 2.INSTALL CYLINDER HEAD COVER GASKET

Hide 11201 3.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 17650 4.INSTALL PURGE VALVE (PURGE VSV)

a.
A393486C01
2.604,1.094 2.26,0.667 true 2.115,1.573 1.792,1.333 true 2.646,1.031 2.865,1.229 0.219,0.198 10 true *1 2.146,1.479 2.365,1.677 0.219,0.198 10 true *2 0.667,0.229 0.865,0.427 0.198,0.198 10 true *a
*1 Fuel Vapor Feed Hose
*2 No. 1 Fuel Vapor Feed Hose
*a Bolt A


Install the purge valve (purge VSV) to the cylinder head cover sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Make sure that there is no oil on the bolt A threads.



b.

Connect the fuel vapor feed hose to the purge valve (purge VSV) and slide the clip to secure it.


c.

Connect the No. 1 fuel vapor feed hose to the intake manifold.


Hide 19500 5.INSTALL IGNITION COIL ASSEMBLY

a.

Install the 4 ignition coil assemblies to the cylinder head cover sub-assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 6.CONNECT ENGINE WIRE

a.

Connect the engine wire with the 3 bolts and nut.

A391998C02
4.979,1.781 5.156,1.458 true 2.052,5.698 2.198,5.948 true 1.448,5.583 1.594,5.833 true 5.26,7.135 5.552,6.781 true 4.896,1.813 5.115,2.01 0.219,0.198 10 true *3 1.948,5.49 2.167,5.688 0.219,0.198 10 true *1 1.198,5.469 1.417,5.667 0.219,0.198 10 true *1 5.135,7.177 5.354,7.375 0.219,0.198 10 true *2
*1 Bolt A *2 Nut
*3 Bolt B - -


Torque:
Bolt A : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
Bolt B, Nut : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Engage the 10 clamps and connect the 21 connectors.


Hide 17705 7.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 28800 8.INSTALL BATTERY

Hide 11.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the continuously variable valve lift controller assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION