Home › Engine / Hybrid System › 8NR-FTS (INTAKE / EXHAUST) › TURBOCHARGER
RM32H0E _51 Engine / Hybrid System _059908 8NR-FTS INTAKE / EXHAUST _0293887 TURBOCHARGER A

8NR-FTS INTAKE / EXHAUST  TURBOCHARGER  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

Before installing the turbocharger sub-assembly, be sure to read Maintenance Precaution.

Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>TURBOCHARGER>PRECAUTION


PROCEDURE

Hide 1.INSTALL STUD BOLT

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
A392851C01
0.135,0.156 0.417,0.375 0.281,0.219 12 false *A 0.115,2.438 0.427,2.688 0.313,0.25 12 false *B 0.094,2.76 0.406,2.917 0.313,0.156 10 false *1 1.781,3.927 2.094,4.083 0.313,0.156 10 false *2 0.385,2.51 0.698,2.667 0.313,0.156 10 false *1 0.302,4.198 0.615,4.354 0.313,0.156 10 false *1 0.969,3.677 1.188,3.844 0.219,0.167 10 true *1 2.302,2.844 2.5,3 0.198,0.156 10 true *2 0.396,0.323 0.708,0.479 0.313,0.156 10 false *1 0.094,0.583 0.406,0.74 0.313,0.156 10 false *1 0.323,2.01 0.635,2.167 0.313,0.156 10 false *1 0.99,1.521 1.198,1.688 0.208,0.167 10 true *1 1.802,1.719 2.115,1.875 0.313,0.156 10 false *2 2.281,0.635 2.49,0.813 0.208,0.177 10 true *2
*A for 2WD
*B for AWD
*1 Stud Bolt (A)
*2 Stud Bolt (B)


Using an E10 "TORX" socket wrench, install the 4 stud bolts (A) to the turbocharger sub-assembly.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


b.

Using an E6 "TORX" socket wrench, install the 2 stud bolts (B) to the turbocharger sub-assembly.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17201 2.INSTALL TURBOCHARGER SUB-ASSEMBLY

a.
A351385C02
2.354,1.219 2.948,1.208 2.948,1.208 2.375,1.438 true 1.594,1.208 0.406,1.229 0.406,1.229 1.594,1.427 true 2.99,1.135 3.302,1.333 0.313,0.198 10 false *a 0.198,1.156 0.51,1.354 0.313,0.198 10 false *a
*a Claw


Install a new outlet compressor gasket to the turbocharger sub-assembly.

HINT:

Make sure that the claws of the outlet compressor gasket are facing the turbocharger sub-assembly.



b.
A351384

Temporarily install the turbocharger sub-assembly to the cylinder head sub-assembly with the 3 bolts.


c.
A351382C02
1.708,0.917 0.948,0.802 0.948,0.802 1.406,1.063 true 1.781,1.333 2.135,1.646 2.135,1.646 1.26,1.604 true 2.229,0.635 2.833,1.063 2.833,1.063 1.958,1.021 true 2.896,1.01 3.24,1.219 0.344,0.208 10 false *a 2.188,1.604 2.531,1.813 0.344,0.208 10 false *a 0.76,0.719 1.104,0.927 0.344,0.208 10 false *a
*a Claw


Install a new inlet turbo oil gasket to the inlet turbo oil pipe sub-assembly.

NOTICE:

Make sure that the inlet turbo oil gasket is installed in the correct direction.


HINT:

Make sure that the claws of the inlet turbo oil gasket are facing the inlet turbo oil pipe sub-assembly.



d.
A355596C02
1.396,1.365 1.854,1.885 1.854,1.885 1.917,1.521 true 1.875,1.26 1.323,0.708 1.323,0.708 1.396,1.115 true 1.198,0.521 1.469,0.74 0.271,0.219 10 true *a 1.771,1.906 2.021,2.104 0.25,0.198 10 true *a
*a Claw


Install a new outlet No. 1 turbo oil gasket to the stiffening crankcase assembly.

HINT:

Make sure that the claws of the outlet No. 1 turbo oil gasket are facing the stiffening crankcase assembly.



e.
A353527C02
2.833,0.927 3.031,1.094 0.198,0.167 10 true *1 2.135,1.563 2.333,1.729 0.198,0.167 10 true *3 1.177,1.26 1.375,1.427 0.198,0.167 10 true *3 2.177,0.313 2.375,0.479 0.198,0.167 10 true *2 1.594,1.021 1.792,1.188 0.198,0.167 10 true *2
*1 Union Bolt
*2 Bolt (A)
*3 Bolt (B)


Install a new gasket to the union bolt.


f.

Temporarily install the inlet turbo oil pipe sub-assembly to the turbocharger sub-assembly and cylinder block sub-assembly with the 2 bolts (A) and union bolt.


g.
A351384N02
1.01,0.26 1.146,0.427 0.135,0.167 10 true 2 2.396,0.354 2.531,0.521 0.135,0.167 10 true 3 2.406,0.896 2.677,1.104 0.271,0.208 10 true 1, 4

Tighten the 3 bolts in the order shown in the illustration.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


h.

Tighten the 2 bolts (A).

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


i.

Temporarily tighten the union bolt.


j.

Temporarily install the 2 bolts (B).


k.

Tighten the union bolt.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:

If the link that connects the gaskets is broken, remove the link by using side cutters or a similar tool.



l.

for 2WD:

i.

Tighten the 2 bolts (B).

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)



m.

for AWD:

i.
A394548C03
0.75,4.26 0.5,3.948 false 1.333,4.292 1.667,4.292 false 2.74,2.073 3.052,2.271 0.313,0.198 10 false *a 1.719,4.208 1.948,4.396 0.229,0.188 10 false *1 0.323,3.823 0.552,4.01 0.229,0.188 10 false *2
*1 8 mm Hexagon Socket Wrench
*2 8 x 10 mm Long Offset Wrench
*a Torque Wrench Fulcrum Length
V100135

Bolt (B)


Using an 8 mm hexagon socket wrench and 8 x 10 mm long offset wrench, tighten the 2 bolts (B).

Torque:
Specified tightening torque : 12 N*m (122 kgf*cm, 9 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a long offset wrench (fulcrum length of 164.5 mm (6.48 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 6.0 N*m (61 kgf*cm, 53 in.*lbf)





n.

Connect the air by-pass valve assembly connector.


Hide 16027 3.CONNECT NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.

Set a new water by-pass gasket.


b.

Temporarily install the No. 1 turbo water pipe sub-assembly with the 2 nuts.


c.

Temporarily install the bolt.


d.
A351383N02
1.229,0.271 1.385,0.448 0.156,0.177 10 true 1 0.875,1.198 1.031,1.375 0.156,0.177 10 true 2 1.969,1.594 2.125,1.771 0.156,0.177 10 true 3

Tighten the 2 nuts and bolt in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 25051 4.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

Hide 6.INSPECT FOR ENGINE OIL LEAK