Home › Engine / Hybrid System › 8NR-FTS (LUBRICATION) › LUBRICATION SYSTEM
RM32H0E _51 Engine / Hybrid System _060037 8NR-FTS LUBRICATION _0294095 LUBRICATION SYSTEM G

8NR-FTS LUBRICATION  LUBRICATION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK ENGINE OIL LEVEL

a.

Warm up and stop the engine, then wait for 5 minutes.


b.

Check that the engine oil level is between the low level and full level marks on the engine oil level dipstick.

If the level is low, check for engine oil leaks and add engine oil to the full level mark.

NOTICE:

Do not fill to above the full level mark.


HINT:

A certain amount of engine oil will be consumed while driving. In the following situations, engine oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.

·

When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.

·

If low quality engine oil or oil of an inappropriate viscosity is used.

·

When driving at high engine speeds or with a heavy load (when towing, etc.), or when accelerating or decelerating frequently while driving.

·

When idling for a long time, or when driving frequently through heavy traffic.


When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.



Hide 2.CHECK ENGINE OIL QUALITY

a.

Check the engine oil for deterioration, water intrusion, discoloration or thinning.

If the quality is visibly poor, replace the engine oil and oil filter element.


Hide 3.INSPECT OIL PRESSURE

CAUTION:
·
A345137

When working near the engine room while the engine has started or the power source mode is ignition switch to ON (IG), do not touch the fan and generator V belt or rotating components such as the fan, etc.

·

Touching the fan and generator V belt or rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.


·
A340359C11
0.375,1.135 0.75,1.281 true 0.135,1.031 0.448,1.229 0.313,0.198 10 false *a
*a High temperature areas


Do not touch the engine or exhaust manifold converter sub-assembly when they are hot.

·

Touching the engine or exhaust manifold converter sub-assembly when they are hot could result in burns.


·
A397110

To prevent burns, do not remove the oil pressure sender gauge assembly while the engine is hot.

·

Removing the oil pressure sender gauge assembly while the engine is hot could result in burns caused by contact with hot engine oil.



NOTICE:

Clean the hose and adapter of the oil pressure gauge before and after measurement.


a.

Check for DTCs.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

If any DTCs are present, perform troubleshooting in accordance with the procedure for each DTC.



b.

Remove the oil pressure sender gauge assembly.

Click hereEngine / Hybrid System>8NR-FTS (LUBRICATION)>OIL PRESSURE SENSOR>REMOVAL

CAUTION:

Make sure the engine is cold when removing the oil pressure sender gauge assembly to prevent burns caused by hot engine oil.



c.
A351842

Install an oil pressure gauge with the adapter.


d.

Warm up the engine.

HINT:

After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).



e.

Check the oil pressure.

Standard Oil Pressure:
Condition Specified Condition
Idling 60 kPa (0.6 kgf/cm2, 9 psi) or higher
2000 rpm 150 kPa (1.5 kgf/cm2, 22 psi) or higher


If the result is not as specified, check the quality of the engine oil and check the oil paths for clogging. Repair or replace if necessary. If the engine oil pressure is still not as specified, check the oil pump assembly.

Click hereEngine / Hybrid System>8NR-FTS (LUBRICATION)>OIL PUMP>INSPECTION


f.

Remove the oil pressure gauge with the adapter.

CAUTION:

Make sure the engine is cold when removing the oil pressure gauge to prevent burns caused by hot engine oil.



g.

Install the oil pressure sender gauge assembly.

Click hereEngine / Hybrid System>8NR-FTS (LUBRICATION)>OIL PRESSURE SENSOR>INSTALLATION


h.

Inspect for engine oil leaks.

Click hereGeneral>MAINTENANCE>8NR-FTS OIL AND OIL FILTER>REPLACEMENT