Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › 2016.10–2020.08
RM32H0E _55 Steering _059604 STEERING COLUMN _0293907 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Unable to Unlock Steering Wheel (Engine cannot Start)  


DESCRIPTION

The steering lock actuator or upper bracket assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if the engine switch is turned on (IG) while shaking the steering wheel, as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or ECM is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the engine cannot be started.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Unable to unlock steering wheel (Engine cannot start)
Entry&Start
·

Unlock Request Receive

·

S Code Check

·

L Code Check

·

Steering Unlock


-

WIRING DIAGRAM

C312033E16
5.177,2.281 5.333,2.479 0.156,0.198 10 false 7 5.177,2.854 5.333,3.052 0.156,0.198 10 false 3 5.188,3.365 5.344,3.563 0.156,0.198 10 false 4 5.177,3.792 5.333,3.99 0.156,0.198 10 false 1 5.385,3.438 6.177,3.646 0.792,0.208 10 false SLP1 5.406,3.865 6.156,4.031 0.75,0.167 10 false GND 5.396,2.948 6.042,3.156 0.646,0.208 10 false IGE 5.406,2.417 5.563,2.615 0.156,0.198 10 false B 3.917,4.292 4.813,4.594 0.896,0.302 10 false F78 3.917,4.458 6.583,5.083 2.667,0.625 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 4.844,5.146 6.833,5.344 1.99,0.198 10 false : LIN Communication Line 4.844,5.448 6.708,5.698 1.865,0.25 10 false : CAN Communication Line 1.771,4.438 2.125,4.656 0.354,0.219 10 false F1 0.323,4.458 1.448,5.042 1.125,0.583 10 false Main Body ECU (Multiplex Network Body ECU) 0.219,1.865 0.531,2.063 0.313,0.198 10 false F21 0.885,0.948 1.469,1.146 0.583,0.198 10 false LIN1 1.302,0.802 1.49,1 0.188,0.198 10 false 2 2.302,2.969 2.958,3.146 0.656,0.177 10 false SLR+ 2.354,3.5 2.917,3.656 0.563,0.156 10 false SLP 2.51,3.906 2.698,4.104 0.188,0.198 10 false E 2.74,3.792 2.927,3.99 0.188,0.198 10 false 18 2.74,3.365 2.927,3.563 0.188,0.198 10 false 14 2.74,2.844 2.927,3.042 0.188,0.198 10 false 25 3.094,2.406 4.333,2.646 1.24,0.24 10 false from Battery 0.208,2.042 1.781,2.552 1.573,0.51 10 false ID Code Box (Immobiliser Code ECU) 4.313,2.573 5.365,2.802 1.052,0.229 10 false STRG LOCK 1.771,4.615 3.365,5 1.594,0.385 10 false Certification ECU (Smart Key ECU Assembly) 5.177,1.646 5.333,1.844 0.156,0.198 10 false 5 2.75,1.677 3.344,1.99 0.594,0.313 10 false 13 2.427,1.833 3.01,2.031 0.583,0.198 10 false LIN 5.385,1.823 5.969,2.021 0.583,0.198 10 false LIN

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Perform either of the following operations to lock/unlock the steering:

-

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG).

-

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.


·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, confirm that the problem does not recur.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the steering lock ECU (steering lock actuator or upper bracket assembly), certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU), registration must be performed (refer to Service Bulletin).

·

When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

If the steering lock ECU (steering lock actuator or upper bracket assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. This function prevents the engine from starting while the steering is locked. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch.



PROCEDURE

1.CHECK ENGINE SWITCH (SWITCH CONDITION)
a.

Check the power source mode change.

i.

When the key is inside the vehicle and the shift lever is in P, check that pressing the engine switch with the brake pedal released causes the power source mode to change as follows:

OK:

Off → On (ACC) → On (IG) → Off




Result:
Proceed to
OK
NG



OK

2.CHECK INDICATOR

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (PROBLEM SYMPTOMS TABLE)

2.CHECK INDICATOR
a.

With the engine switch on (IG), check that Steering Lock active is displayed on the multi-information display in the combination meter assembly.


Result:
Result Proceed to
Steering Lock active is displayed. A
Steering Lock active is not displayed. B



A

3.CHECK STEERING UNLOCK

B

4.CHECK FOR DTC
3.CHECK STEERING UNLOCK
a.

Turn the steering wheel left and right, and then press the engine switch.


b.

Check that the steering is unlocked.


Result:
Result Proceed to
The steering is unlocked. A
The steering is not unlocked. B



A

END

B

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Using the GTS, check if the certification ECU (smart key ECU assembly) DTC is output.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

5.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)

B

GO TO DIAGNOSTIC PROCEDURE INDICATED BY OUTPUT DTC

5.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
a.

Use the Data List to check if the steering lock request is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Unlock Request Receive Reception state of steering unlock request signal by certification ECU (smart key ECU assembly) sent to ID code box (immobiliser code ECU)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".



OK or NG OK: Unlock request received within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
NG: Except above
·

If the unlock signal has not been received, the engine cannot be started.

·

If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Unlock Request Receive
50003 125 67
OK:

Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (S CODE CHECK)

NG

14.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
6.READ VALUE USING GTS (S CODE CHECK)
a.

Use the Data List to check if S code certification is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
S Code Check
50003 125 65
OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (L CODE CHECK)

NG

13.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
7.READ VALUE USING GTS (L CODE CHECK)
a.

Use the Data List to check if L code certification is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The steering lock ECU (steering lock actuator or upper bracket assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

8.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

12.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
8.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.
C350527C22
1.5,0.646 2,0.896 0.5,0.25 0.771,2.729 1.135,1.948 true 2.76,2.771 2.271,1.958 true 0.177,0.208 0.49,0.365 0.313,0.156 10 false *a 0.698,2.74 1.01,2.896 0.313,0.156 10 false B 2.646,2.833 3.052,3 0.406,0.167 10 false GND 1.635,0.667 1.948,0.823 0.313,0.156 10 false F78
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F78-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.


Standard Voltage:
Tester Connection Condition Specified Condition
F78-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (GROUND)
a.

Disconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C350526C11
1.531,0.792 2.031,1.042 0.5,0.25 0.75,1.938 1.281,2.427 true 0.323,0.208 0.635,0.365 0.313,0.156 10 false *a 1.656,0.802 1.969,0.958 0.313,0.156 10 false F78 0.375,1.844 0.688,2 0.313,0.156 10 false GND
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F78-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.



c.
C241547C81
0.083,0.917 0.583,1.167 0.5,0.25 0.354,2.896 1.729,3.063 1.375,0.167 2.313,2.958 2.719,3.073 0.406,0.115 1.563,4.031 2.521,4.198 0.958,0.167 2.302,1.104 2.823,1.917 true 1.573,2.896 2.896,2.625 2.896,2.625 2.635,2.958 true 2.115,4.198 2.115,4.458 true 1.854,1.104 1.083,1.917 true 0.24,0.146 0.563,0.375 0.323,0.229 10 false *a 2.927,2.521 3.104,2.708 0.177,0.188 10 false *b 2.042,4.469 2.344,4.667 0.302,0.198 10 false *c 0.219,0.927 0.531,1.094 0.313,0.167 10 false F78 0.938,1.948 1.458,2.208 0.521,0.26 10 false IGE 2.708,1.958 3.063,2.125 0.354,0.167 10 false GND 3.052,4.01 3.427,4.177 0.375,0.167 10 false GND
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
*b Steering Lock Motor not Operating
*c Steering Lock Motor Operating


Check the signal waveform according to the condition(s) in the table below.

Standard Frequency:
Item Content
Tester Connection F78-3 (IGE) - F78-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Operating → Not operating


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG).

-

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.





Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
10.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


c.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


d.

Check for deformation and corrosion of the connector case and terminals.

OK:

There is no deformation or corrosion of the connector case or terminals.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F78-3 (IGE) - F1-25 (SLR+) Always Below 1 Ω
F78-3 (IGE) or F1-25 (SLR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Reconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


c.
C350527C20
1.5,0.583 2,0.833 0.5,0.25 2.583,2.75 1.865,1.979 true 0.177,0.208 0.49,0.365 0.313,0.156 10 false *a 2.542,2.802 2.948,2.969 0.406,0.167 10 false IGE 1.625,0.594 1.938,0.75 0.313,0.156 10 false F78
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F78-3 (IGE) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

12.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Perform registration (refer to Service Bulletin).


c.

Turn the engine switch on (IG).


d.

Use the Data List to check if L code certification is functioning properly again.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

13.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.


b.

Perform registration (refer to Service Bulletin).


c.

Use the Data List to check if S code certification is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
S Code Check
50003 125 65
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

14.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.
C350527C21
1.448,0.698 1.948,0.948 0.5,0.25 2.552,2.74 1.719,1.948 true 0.177,0.208 0.49,0.365 0.313,0.156 10 false *a 2.469,2.771 2.906,3.063 0.438,0.292 10 false SLP1 1.583,0.719 1.896,0.958 0.313,0.24 10 false F78
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F78-4 (SLP1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

15.READ VALUE USING GTS (STEERING UNLOCK)

NG

17.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
15.READ VALUE USING GTS (STEERING UNLOCK)
a.

Check that the steering is locked.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock State of whether steering lock ECU (steering lock actuator or upper bracket assembly) determined steering is unlocked Set or Unset Set: Steering unlocked
Unset: Steering locked
If this item displays "Unset", the steering does not unlock (engine cannot be started).
Body Electrical > Entry&Start > Data List
Tester Display
Steering Unlock
50003 125 48
OK:

Set is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

16.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

16.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.


b.

Perform registration (refer to Service Bulletin).


c.

Turn the engine switch on (IG).


d.

Use the Data List to check if the steering lock request is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Unlock Request Receive Reception state of steering unlock request signal by certification ECU (smart key ECU assembly) sent to ID code box (immobiliser code ECU)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".



OK or NG OK: Unlock request received within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
NG: Except above
·

If the unlock signal has not been received, the engine cannot be started.

·

If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Unlock Request Receive
50003 125 67
OK:

Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

17.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


c.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


d.

Check for deformation and corrosion of the connector case and terminals.

OK:

There is no deformation or corrosion of the connector case or terminals.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F78-4 (SLP1) - F1-14 (SLP) Always Below 1 Ω
F78-4 (SLP1) or F1-14 (SLP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
a.

Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Perform registration (refer to Service Bulletin).


c.

Turn the engine switch on (IG).


d.

Use the Data List to check if the steering lock request is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Unlock Request Receive Reception state of steering unlock request signal by certification ECU (smart key ECU assembly) sent to ID code box (immobiliser code ECU)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".



OK or NG OK: Unlock request received within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
NG: Except above
·

If the unlock signal has not been received, the engine cannot be started.

·

If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Unlock Request Receive
50003 125 67
OK:

Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)