The rear pretensioner squib LH circuit consists of the airbag sensor assembly and rear seat 3 point type outer belt assembly LH.
The airbag sensor assembly uses this circuit to deploy the pretensioner when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the rear pretensioner squib LH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1925/78 | Short in Rear Pretensioner Squib LH Circuit | Any of the following conditions is met:
·
The airbag sensor assembly detects a line short in the rear pretensioner squib LH circuit during the primary check. ·
Rear pretensioner squib LH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Rear pretensioner squib LH (Rear seat 3 point type outer belt assembly LH) ·
Airbag sensor assembly |
Applies to check mode |
| B1926/78 | Open in Rear Pretensioner Squib LH Circuit | Any of the following conditions is met:
·
The airbag sensor assembly detects an open in the rear pretensioner squib LH circuit. ·
Rear pretensioner squib LH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Rear pretensioner squib LH (Rear seat 3 point type outer belt assembly LH) ·
Airbag sensor assembly |
Applies to check mode |
| B1927/78 | Short to GND in Rear Pretensioner Squib LH Circuit | Any of the following conditions is met:
·
The airbag sensor assembly detects a short to ground in the rear pretensioner squib LH circuit. ·
Rear pretensioner squib LH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Rear pretensioner squib LH (Rear seat 3 point type outer belt assembly LH) ·
Airbag sensor assembly |
Applies to check mode |
| B1928/78 | Short to B+ in Rear Pretensioner Squib LH Circuit | Any of the following conditions is met:
·
The airbag sensor assembly detects a short to B+ in the rear pretensioner squib LH circuit. ·
Rear pretensioner squib LH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Rear pretensioner squib LH (Rear seat 3 point type outer belt assembly LH) ·
Airbag sensor assembly |
Applies to check mode |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ |
| Malfunction Status | The airbag sensor assembly detects a line short in the rear pretensioner squib LH circuit during the primary check | ○ | - | - |
| Rear pretensioner squib LH malfunction | - | ○ | - | |
| Airbag sensor assembly malfunction | - | - | ○ | |
| Detection Time | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ |
| Malfunction Status | The airbag sensor assembly detects an open in the rear pretensioner squib LH circuit | ○ | - | - |
| Rear pretensioner squib LH malfunction | - | ○ | - | |
| Airbag sensor assembly malfunction | - | - | ○ | |
| Detection Time | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ |
| Malfunction Status | The airbag sensor assembly detects a short to ground in the rear pretensioner squib LH circuit | ○ | - | - |
| Rear pretensioner squib LH malfunction | - | ○ | - | |
| Airbag sensor assembly malfunction | - | - | ○ | |
| Detection Time | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ |
| Malfunction Status | The airbag sensor assembly detects a short to B+ in the rear pretensioner squib LH circuit | ○ | - | - |
| Rear pretensioner squib LH malfunction | - | ○ | - | |
| Airbag sensor assembly malfunction | - | - | ○ | |
| Detection Time | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Perform the simulation method by selecting check mode (Signal Check) using the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *A | w/o Dual-stage SRS |
| *B | w/ Dual-stage SRS |
| *1 | Rear Seat 3 Point Type Outer Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the rear seat 3 point type outer belt assembly LH and airbag sensor assembly.
The connectors are properly connected.
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the rear seat 3 point type outer belt assembly LH and airbag sensor assembly.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
Check that the floor wire connector (on the rear seat 3 point type outer belt assembly LH side) is not loose, deformed or damaged.
The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.
Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.
The short springs are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connector to the airbag sensor assembly.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Rear Seat 3 Point Type Outer Belt Assembly LH | *2 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector
(to Rear Seat 3 Point Type Outer Belt Assembly LH) |
- | - |
Connect SST (resistance 2.1 Ω) to connector C.
Never connect a tester to the rear seat 3 point type outer belt assembly LH for measurement, as this may lead to a serious injury due to pretensioner deployment.
Do not forcibly insert SST into the terminals of the connector when connecting it.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1925/78, B1926/78, B1927/78 or B1928/78 is not output.
Codes other than DTCs B1925/78, B1926/78, B1927/78 and B1928/78 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Disconnect SST from connector C.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the floor wire from the airbag sensor assembly.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Rear Seat 3 Point Type Outer Belt Assembly LH | *2 | Airbag Sensor Assembly |
| *3 | Floor Wire | - | - |
| *a | Front view of wire harness connector
(to Rear Seat 3 Point Type Outer Belt Assembly LH) |
- | - |
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M46-1 (RL+) - Body ground | Ignition switch ON | Below 1 V |
| M46-2 (RL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M46-1 (RL+) - M46-2 (RL-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M46-1 (RL+) - Body ground | Always | 1 MΩ or higher |
| M46-2 (RL-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M46-1 (RL+) - M46-2 (RL-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | w/o Dual-stage SRS |
| *B | w/ Dual-stage SRS |
| *1 | Rear Seat 3 Point Type Outer Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the rear seat 3 point type outer belt assembly LH and airbag sensor assembly.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1925/78, B1926/78, B1927/78 or B1928/78 is not output.
Codes other than DTCs B1925/78, B1926/78, B1927/78 and B1928/78 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG