The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear seat outer belt assembly removal/installation are shown below.
*1: When performing learning using the GTS.
*2: w/ Stop and start system
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 8NR-FTS:
for 3ZR-FAE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If an SRS part is accidentally deployed, it may cause a serious injury.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
3.REMOVE REAR SEAT ASSEMBLY
64330D
4.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)
64910J
5.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
58410B
6.REMOVE DECK BOARD ASSEMBLY (w/ Deck Board)
64777J
7.REMOVE SPARE WHEEL CUSHION (w/ Deck Board)
64997
8.REMOVE DECK FLOOR BOX LH (w/ Deck Floor Box)
64995
9.REMOVE DECK FLOOR BOX RH (w/ Deck Floor Box)
67918A
10.REMOVE REAR DOOR SCUFF PLATE
62332A
11.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP
71304C
12.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY
62552F
13.REMOVE REAR SEAT SIDE GARNISH
64716D
14.REMOVE DECK TRIM REAR COVER
81330
15.REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)
64715C
16.REMOVE DECK TRIM SIDE COVER (w/ Cover)
64740C
17.REMOVE DECK TRIM SIDE PANEL ASSEMBLY
62480A
18.REMOVE ROOF SIDE INNER GARNISH ASSEMBLY
73370
19.REMOVE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH (for LH Side)
Remove the bolt to disconnect the floor anchor of the rear seat 3 point type outer belt assembly LH.
w/o Pretensioner:
Loosen the nut.
Remove the 3 bolts.
Disengage the guides to remove the rear seat 3 point type outer belt assembly LH with bracket.
Remove the nut.
Disengage the guides to remove the rear seat 3 point type outer belt assembly LH from the outer belt anchor bracket sub-assembly LH.
w/ Pretensioner:
Loosen the nut.
Remove the 3 bolts.
Disengage the guides to separate the rear seat 3 point type outer belt assembly LH with bracket.
| *a | Locking Button |
| *b | Protective Tape |
Disengage the clamp.
Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.
Remove the nut.
Disengage the guides to remove the rear seat 3 point type outer belt assembly LH from the outer belt anchor bracket sub-assembly LH.
73360
20.REMOVE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH (for RH Side)
Remove the bolt to disconnect the floor anchor of the rear seat 3 point type outer belt assembly RH.
w/o Pretensioner:
Loosen the nut.
Remove the 3 bolts.
Disengage the guides to remove the rear seat 3 point type outer belt assembly RH with bracket.
Remove the nut.
Disengage the guides to remove the rear seat 3 point type outer belt assembly RH from the outer belt anchor bracket sub-assembly RH.
w/ Pretensioner:
| *a | Locking Button |
| *b | Protective Tape |
Disengage the clamp.
Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.
Loosen the nut.
Remove the 3 bolts.
Disengage the guides to remove the rear seat 3 point type outer belt assembly RH with bracket.
Remove the nut.
Disengage the guides to remove the rear seat 3 point type outer belt assembly RH from the outer belt anchor bracket sub-assembly RH.