Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › KNEE AIRBAG ASSEMBLY › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294194 KNEE AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  KNEE AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the lower No. 1 instrument panel airbag assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)*2 Stop and start system (Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

*2: w/ Stop and start system

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
·
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55545 3.REMOVE FUSE BOX OPENING COVER

Hide 55470 4.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

Hide 55434B 5.REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL

Hide 73900 6.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY WITH DOOR

CAUTION:
B417755C02
0.604,0.521 0.76,0.719 0.156,0.198 10 false .
V100155

Deployment Side


When storing the lower No. 1 instrument panel airbag assembly with door, keep the airbag deployment side facing upward.


a.

Check that the ignition switch off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B454046

Remove the 2 bolts.


d.

Disengage the hooks to separate the lower No. 1 instrument panel airbag assembly with door.

NOTICE:

When separating the lower No. 1 instrument panel airbag assembly with door, do not pull the airbag wire harness.



e.
B454047C01
0.406,2.313 0.719,2.208 true 0.604,3.094 0.99,2.469 true 1.51,1.167 1.167,0.917 true 0.188,2.229 0.5,2.385 0.313,0.156 10 false *a 0.427,3.021 0.74,3.177 0.313,0.156 10 false *b 1.542,1.094 1.854,1.25 0.313,0.156 10 false *c
*a Protective Tape
*b Airbag Connector
*c Airbag Connector Lock


Using a screwdriver with its tip wrapped in protective tape, release the airbag connector lock.


f.

Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly with door.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



Hide 73997 7.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG DOOR (for TMMT Made)

a.
B460342

Disengage the hooks.


b.
B460341

Disengage the hooks to remove the lower No. 1 instrument panel airbag door from the lower No. 1 instrument panel airbag assembly.