Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)
RM32H0E _58 Vehicle Interior _059647 DOOR LOCK _0294251 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)  Only Wireless Control Function is Inoperative  


DESCRIPTION

The door control receiver receives signals from the door control transmitter assembly and sends these signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher signals to the combination meter assembly.

WIRING DIAGRAM

w/ Tire Pressure Warning System


E358355E01
3.594,0.292 4.51,0.5 0.917,0.208 10 false from Battery 2.448,0.448 3.594,0.656 1.146,0.208 10 false ECU-DCC NO. 2 1.833,0.302 2.167,0.479 0.333,0.177 10 false +B 1.74,0.698 2.073,0.875 0.333,0.177 10 false RDA 1.74,1.927 2.073,2.104 0.333,0.177 10 false PRG 1.76,2.458 2.094,2.635 0.333,0.177 10 false GND 2.135,2.375 2.469,2.552 0.333,0.177 10 false 12 2.167,1.938 2.5,2.115 0.333,0.177 10 false 5 2.167,0.719 2.5,0.896 0.333,0.177 10 false 4 2.156,0.198 2.49,0.375 0.333,0.177 10 false 7 1.281,1.438 1.615,1.615 0.333,0.177 10 false 12 V 0.906,0.979 1.24,1.156 0.333,0.177 10 false IC 0.76,2.844 1.094,3.021 0.333,0.177 10 false M23 0.76,3.01 2.135,3.406 1.375,0.396 10 false Door Control Receiver 5.146,3.115 6.802,3.656 1.656,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 5.146,2.948 5.479,3.125 0.333,0.177 10 false F15 5.281,1.927 5.615,2.104 0.333,0.177 10 false PRG 5.281,0.708 5.615,0.885 0.333,0.177 10 false RDA 5.073,0.708 5.406,0.885 0.333,0.177 10 false 4 5.083,1.938 5.417,2.115 0.333,0.177 10 false 5 5.719,0.219 6.052,0.396 0.333,0.177 10 false 12 V 6.271,1.365 6.604,1.542 0.333,0.177 10 false CPU


w/o Tire Pressure Warning System


E329249E05
0.896,0.979 1.229,1.188 0.333,0.208 10 false IC 1.302,1.417 1.76,1.615 0.458,0.198 10 false 12 V 0.76,2.875 1.219,3.073 0.458,0.198 10 false M30 0.76,3.031 2.594,3.229 1.833,0.198 10 false Door Control Receiver 1.74,0.698 2.198,0.896 0.458,0.198 10 false RDA 1.823,0.302 2.135,0.5 0.313,0.198 10 false +B 2.156,0.188 2.313,0.385 0.156,0.198 10 false 5 2.156,0.698 2.313,0.896 0.156,0.198 10 false 2 1.729,1.938 2.188,2.135 0.458,0.198 10 false PRG 2.167,1.927 2.323,2.125 0.156,0.198 10 false 3 1.729,2.479 2.188,2.677 0.458,0.198 10 false GND 2.156,2.365 2.313,2.563 0.156,0.198 10 false 1 2.417,0.448 3.51,0.646 1.094,0.198 10 false ECU-DCC NO. 2 3.615,0.292 4.531,0.49 0.917,0.198 10 false from Battery 5.74,0.177 6.198,0.375 0.458,0.198 10 false 12 V 5.292,0.708 5.75,0.906 0.458,0.198 10 false RDA 5.292,1.938 5.75,2.135 0.458,0.198 10 false PRG 6.271,1.344 6.729,1.542 0.458,0.198 10 false CPU 5.135,2.979 5.594,3.177 0.458,0.198 10 false F15 5.135,3.146 6.823,3.781 1.688,0.635 10 false Main Body ECU (Multiplex Network Body ECU) 5.052,1.938 5.208,2.135 0.156,0.198 10 false 5 5.063,0.708 5.219,0.906 0.156,0.198 10 false 4


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.

·

When replacing the door control receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.*

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATIONafter registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATIONof the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.*

*: w/ Tire Pressure Warning System




PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Locked doors unlock



Result:
Proceed to
OK
NG



OK

2.CHECK KEY REMINDER WARNING SYSTEM

NG

2.CHECK KEY REMINDER WARNING SYSTEM
a.

Check that the key reminder warning buzzer operates properly.

Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK

OK:

Key reminder warning buzzer operates properly.



Result:
Proceed to
OK
NG



OK

3.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY

NG

3.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY
a.

When a known good registered door control transmitter assembly is used, check that the wireless functions operate properly.


Result:
Result Proceed to
Wireless door lock/unlock function operates properly with a known good door control transmitter assembly. A
Wireless door lock function does not operate. B



A

4.CHECK TRANSMITTER BATTERY (VOLTAGE)

B

5.CHECK WAVE ENVIRONMENT
4.CHECK TRANSMITTER BATTERY (VOLTAGE)
a.

Inspect the battery capacity.

i.

Remove the battery from the door control transmitter assembly that does not operate (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/o Entry and Start System)>REMOVAL). Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative (-) terminal.

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between the terminals, or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.




b.
B330067

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

NOTICE:

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter assembly from being damaged.



c.
B330068

Check the transmitter battery voltage.

HINT:

Measure the transmitter battery voltage while pressing the lock or unlock switch on the door control transmitter assembly.


Standard Voltage:
Item Content
Tester Connection Transmitter battery positive (+) - Transmitter battery negative (-)
Condition Ignition switch off, all doors closed and lock or unlock switch is pressed
Specified Condition 2.5 to 3.2 V



Result:
Proceed to
OK
NG



OK

REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY

NG

5.CHECK WAVE ENVIRONMENT
a.

Bring the door control transmitter assembly near the door control receiver, and perform a wireless operation check.

HINT:
·

When the door control transmitter assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



OK:

Wireless functions operate properly.



Result:
Proceed to
OK
NG



OK

END (AFFECTED BY WAVE INTERFERENCE)

NG

6.SWITCH TO SELF-DIAGNOSTIC MODE (USING GTS)
6.SWITCH TO SELF-DIAGNOSTIC MODE (USING GTS)
a.

Connect the GTS to the DLC3.


b.

Turn the Ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Wireless Diagnosis Mode.

Body Electrical > Main Body > Utility
Tester Display
Wireless Code Registration
50005 123 107

e.

Proceed to the next step in accordance with the prompts on the GTS screen.


f.
B220865E28
0.125,0.031 1.51,0.406 1.385,0.375 10 Interior Light Output: 0.646,1.406 1.042,1.677 0.396,0.271 10 ON 0.583,1.688 1,2.01 0.417,0.323 10 OFF 1.542,2.167 1.948,2.521 0.406,0.354 10 T1 2.156,2.167 2.458,2.417 0.302,0.25 10 T2 1.979,2.604 3.167,2.885 1.188,0.281 10 T1: 0.25 seconds 1.979,2.917 3.26,3.208 1.281,0.292 10 T2: 0.5 seconds 1.802,2.167 2.167,2.563 0.365,0.396 10 T1

Check that the system has switched to self-diagnostic mode by checking the interior light output pattern.


Result:
Proceed to
NEXT



NEXT

7.CHECK SELF DIAGNOSTIC MODE
7.CHECK SELF DIAGNOSTIC MODE
a.

Inspect the diagnostic outputs when the door control transmitter assembly switch is pressed. The diagnostic outputs can be checked by the flash patterns of the interior lights.

B462101E01
0.083,0.083 3.448,0.281 3.365,0.198 10 false Interior Light Output: 0.344,1.333 3.708,1.531 3.365,0.198 10 false (Lock/Unlock Switch): 0.344,1.01 3.708,1.208 3.365,0.198 10 false Normal Wave (A) 0.521,1.948 1.188,2.146 0.667,0.198 10 false ON 0.448,2.344 1.115,2.542 0.667,0.198 10 false OFF 1.24,2.792 1.906,2.99 0.667,0.198 10 false T1 1.75,2.792 2.417,2.99 0.667,0.198 10 false T2 4.198,1.531 4.865,1.729 0.667,0.198 10 false OFF 4.271,1.146 4.938,1.344 0.667,0.198 10 false ON 4.125,0.417 6.333,0.667 2.208,0.25 10 false Unmatching Recognition Code (B): 4.125,2.75 5.917,3 1.792,0.25 10 false No Diagnostic Output (C): 4.958,1.979 6.583,2.229 1.625,0.25 10 false Wave is being received 4.198,3.354 4.865,3.552 0.667,0.198 10 false OFF 0.448,3.5 3.813,3.698 3.365,0.198 10 false T1: 0.25 seconds (Interior Light) 0.448,3.833 3.813,4.031 3.365,0.198 10 false T2: 0.5 seconds (Interior Light)


Result:
Result Proceed to
Normal wave (light flash pattern) is output. (for LHD) A
Normal wave (light flash pattern) is output. (for RHD) B
Unmatching recognition code is output. C
No diagnostic outputs. D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

8.CHECK REGISTER RECOGNITION CODE

D

9.CHECK DOOR CONTROL RECEIVER (RESPONSE)
8.CHECK REGISTER RECOGNITION CODE
a.

Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)>REGISTRATION

OK:

Recognition code can be registered.



Result:
Proceed to
OK
NG



OK

END (GO TO OPERATION CHECK)

NG

13.REPLACE DOOR CONTROL RECEIVER
9.CHECK DOOR CONTROL RECEIVER (RESPONSE)
a.

Prepare the door control transmitter assembly from another vehicle.


b.

Press and hold down the door control transmitter assembly switch.


c.

Check that an unmatching recognition code is output.

OK:

Unmatching recognition code is output.



Result:
Proceed to
OK
NG



OK

REPLACE DOOR CONTROL (CUT KEY) TRANSMITTER ASSEMBLY

NG

10.CHECK DOOR CONTROL RECEIVER (+B, GND)
10.CHECK DOOR CONTROL RECEIVER (+B, GND)
a.
E198671C38
1.385,0.385 1.802,0.656 0.417,0.271 0.771,1.865 1.229,1.667 true 2.49,1.885 2.031,1.677 true 1.469,0.427 1.927,0.625 0.458,0.198 10 false M23 0.542,1.833 0.854,2.031 0.313,0.198 10 false +B 2.542,1.875 3.208,2.073 0.667,0.198 10 false GND 0.74,0.552 1.052,0.75 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Door Control Receiver)


w/ Tire Pressure Warning System:

i.

Disconnect the M23 door control receiver.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M23-12 (GND) - Body ground Always Below 1 Ω



iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M23-7 (+B) - Body ground Always 11 to 14 V




b.
B281165C30
1.49,0.146 1.906,0.375 0.417,0.229 2.594,1.406 2.208,1.406 true 1.219,1.406 0.833,1.406 true 0.125,0.094 0.302,0.24 0.177,0.146 10 false *a 0.469,1.333 1.073,1.573 0.604,0.24 10 false GND 2.667,1.323 3.146,1.563 0.479,0.24 10 false +B 1.573,0.177 2.406,0.51 0.833,0.333 10 false M30
*a Front view of wire harness connector
(to Door Control Receiver)


w/o Tire Pressure Warning System:

i.

Disconnect the M30 door control receiver.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M30-1 (GND) - Body ground Always Below 1 Ω



iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M30-5 (+B) - Body ground Always 11 to 14 V




Result:
Proceed to
OK
NG



OK

11.CHECK DOOR CONTROL RECEIVER (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK DOOR CONTROL RECEIVER (OUTPUT)
a.

w/ Tire Pressure Warning System:

i.

Connect the M23 door control receiver.


ii.
B462700C01
1.417,0.167 1.917,0.417 0.5,0.25 0.938,0.573 1.604,0.99 true 1.542,0.188 2,0.385 0.458,0.198 10 false M23 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 0.573,0.469 1.031,0.667 0.458,0.198 10 false RDA
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M23-4 (RDA) - Body ground Ignition switch lock, all doors closed and door control transmitter assembly switch not pressed 11 to 14 V
Ignition switch lock, all doors closed and door control transmitter assembly switch pressed Pulse generation
(0 to 12 V)




b.

w/o Tire Pressure Warning System:

i.

Connect the M30 door control receiver.


ii.
B281169C15
1.49,0.375 1.927,0.604 0.438,0.229 1.896,1.271 2.406,1.854 true 0.24,0.167 0.583,0.49 0.344,0.323 10 false *a 2.438,1.865 2.927,2.052 0.49,0.188 10 false RDA 1.594,0.417 1.969,0.594 0.375,0.177 10 false M30
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M30-2 (RDA) - Body ground Ignition switch lock, all doors closed and door control transmitter assembly switch not pressed 11 to 14 V
Ignition switch lock, all doors closed and door control transmitter assembly switch pressed Pulse generation
(0 to 12 V)




Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - DOOR CONTROL RECEIVER)

NG

REPLACE DOOR CONTROL RECEIVER

12.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - DOOR CONTROL RECEIVER)
a.

w/ Tire Pressure Warning System:

i.

Disconnect the F15 main body ECU (multiplex network body ECU) connector.


ii.

Disconnect the M23 door control receiver connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M23-4 (RDA) - F15-4 (RDA) Always Below 1 Ω
M23-5 (PRG) - F15-5 (PRG) Always Below 1 Ω
M23-4 (RDA) - Body ground Always 10 kΩ or higher
M23-5 (PRG) - Body ground Always 10 kΩ or higher
F15-4 (RDA) - Body ground Always 10 kΩ or higher
F15-5 (PRG) - Body ground Always 10 kΩ or higher




b.

w/o Tire Pressure Warning System:

i.

Disconnect the F15 main body ECU (multiplex network body ECU) connector.


ii.

Disconnect the M30 door control receiver connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M30-2 (RDA) - F15-4 (RDA) Always Below 1 Ω
M30-3 (PRG) - F15-5 (PRG) Always Below 1 Ω
M30-2 (RDA) - Body ground Always 10 kΩ or higher
M30-3 (PRG) - Body ground Always 10 kΩ or higher
F15-4 (RDA) - Body ground Always 10 kΩ or higher
F15-5 (PRG) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

13.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new or known good one.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK REGISTER RECOGNITION CODE
14.CHECK REGISTER RECOGNITION CODE

Result:
Proceed to
NEXT



NEXT

15.CHECK DOOR CONTROL RECEIVER (OPERATION)
15.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

OK:

Doors can be locked and unlocked by the door control transmitter assembly.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)