Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for TMC Made)
RM32H0E _52 Drivetrain _060137 DRIVE SHAFT / PROPELLER SHAFT _0294913 FRONT DRIVE SHAFT ASSEMBLY(for TMC Made) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for TMC Made)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43030B 1.INSTALL FRONT DRIVE INBOARD JOINT HOLE SNAP RING

a.

Install a new front drive inboard joint hole snap ring.


Hide 43420 2.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

a.

for CVT:

i.

Coat the splines of the front drive inboard joint assembly with Toyota Genuine CVT Fluid FE.



b.

for Manual Transaxle:

i.

Coat the splines of the front drive inboard joint assembly with Toyota Genuine Manual Transmission Gear Oil LV.



c.

Coat the lip of the front drive shaft oil seal LH with MP grease.


d.
C345600

Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.

NOTICE:
·

Face the end gap of the front drive shaft hole snap ring downward.

·

Do not damage the front drive shaft oil seal LH.

·

Do not damage the front axle inboard joint boot.

·

Make sure to center the front drive shaft assembly LH during installation to prevent damage to the front drive shaft hole snap ring.



HINT:

Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.



e.
C344867C01
0,0 0,0 false
V100135

Toyota Body Grease W


Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz.) of Toyota Body Grease W to each of the 4 areas shown in the illustration.


f.
C345601C02
2.854,0.708 2.156,1.625 2.156,1.625 2.719,0.448 true 2.073,1.646 2.406,1.833 0.333,0.188 10 false *a
*a Matchmark


Align the matchmarks and install the front drive shaft assembly LH to the front axle hub sub-assembly.

NOTICE:
·

Do not push the front axle assembly towards the outside of the vehicle any further than necessary.

·

Check that there is no foreign matter on the deflector or contact surfaces.

·

Do not damage the front drive shaft outboard joint boot.

·

Do not damage the front disc brake dust cover.

·

Do not damage the deflector.




Hide 43410 3.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

a.

for CVT:

i.

Coat the splines of the front drive inboard joint assembly with Toyota Genuine CVT Fluid FE.


ii.

Perform the same procedure as for the LH side.



b.

for Manual Transaxle:

i.

Coat the splines of the front drive inboard joint assembly with Toyota Genuine Manual Transmission Gear Oil LV.


ii.

Perform the same procedure as for the LH side.



c.

for AWD:

i.

Coat the splines of the front drive inboard joint assembly with Toyota Genuine CVT Fluid FE.


ii.

Install a new drive shaft bearing bracket hole snap ring to the front drive shaft assembly RH.


iii.

Align the shaft splines and securely install the front drive shaft assembly RH.

NOTICE:
·

Be careful not to damage the front drive shaft oil seal RH, inboard joint boot and drive shaft dust cover.

·

When inserting the front drive shaft assembly RH, keep it level.




iv.

Install the drive shaft bearing bracket hole snap ring and a new bolt.

Torque:
32.4 N*m (330 kgf*cm, 24 ft.*lbf)


v.

Perform the same procedure as for the LH side.



Hide 4.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Hide 5.INSTALL FRONT STABILIZER LINK ASSEMBLY

Hide 6.CONNECT TIE ROD END SUB-ASSEMBLY

Hide 7.INSTALL FRONT SPEED SENSOR

Hide 43502H 8.INSTALL FRONT AXLE SHAFT NUT

a.

Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new front drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.
C345602

Using a 30 mm deep socket wrench, install the front axle shaft nut.

Torque:
216 N*m (2203 kgf*cm, 159 ft.*lbf)

HINT:

Keep depressing the brake pedal to prevent the drive shaft from rotating.



c.

Using a chisel and a hammer, stake the front axle shaft nut.


Hide 9.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)

Hide 10.ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)

Hide 11.ADD TRANSFER OIL (for AWD)

Hide 12.INSPECT MANUAL TRANSAXLE OIL (for Manual Transaxle)

Hide 13.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK (for CVT)

Hide 14.INSPECT MANUAL TRANSAXLE OIL LEAK (for Manual Transaxle)

Hide 15.INSPECT TRANSFER OIL LEAK (for AWD)

Hide 16.INSTALL FRONT WHEEL ASSEMBLY

Hide 51444A 18.INSTALL REAR ENGINE UNDER COVER LH

Hide 51443C 19.INSTALL REAR ENGINE UNDER COVER RH

Hide 51441 20.INSTALL NO. 1 ENGINE UNDER COVER