Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1428  Motor Circuit Malfunction  


DESCRIPTION

This DTC is stored when the skid control ECU (brake actuator assembly) judges that an abnormality occurred in the circuit used to operate the pump motor.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1428 Motor Circuit Malfunction A malfunction occurs in the pump motor circuit. Pump motor circuit

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+BM TERMINAL)
a.
C360727C16
1.396,0.177 1.802,0.438 0.406,0.26 1.063,1.854 0.667,1.229 true 1.104,1.792 1.75,1.99 0.646,0.198 10 false +BM 0.104,0.063 0.365,0.24 0.26,0.177 10 false *a 1.458,0.219 1.844,0.396 0.385,0.177 10 false A42
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-1 (+BM) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.
C360727C25
0.094,0.313 0.542,0.583 0.448,0.271 2.313,1.771 2.74,1.25 true 0.156,0.135 0.469,0.292 0.313,0.156 10 false *a 0.177,0.365 0.563,0.563 0.385,0.198 10 false A42 1.896,1.781 2.406,1.948 0.51,0.167 10 false GND2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-14 (GND2) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1428 is not output. A
DTC C1428 is output. (for LHD) B
DTC C1428 is output. (for RHD) C



A

B

C