Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2016.10–2019.09
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1246  Master Cylinder Pressure Sensor Malfunction  


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU in the brake actuator assembly.

C106656E33
3.927,4.115 5.552,4.313 1.625,0.198 10 Brake Actuator Assembly 2.896,1.344 4.042,1.531 1.146,0.188 10 Skid Control ECU 5.406,2.583 6.5,2.938 1.094,0.354 10 Master Cylinder Pressure Sensor 0.563,1.958 1.438,2.208 0.875,0.25 10 from Battery 0.26,2.625 1.344,2.969 1.083,0.344 10 from Stop Light Switch Assembly 0.354,3.375 1.396,3.604 1.042,0.229 10 to Body Ground 2.76,1.979 3.073,2.177 0.313,0.198 10 +BS 2.76,2.688 3.104,2.896 0.344,0.208 10 STP 2.76,3.396 3.135,3.594 0.375,0.198 10 GND 3.865,1.979 4.333,2.188 0.469,0.208 10 VCM 3.865,2.677 4.313,2.885 0.448,0.208 10 PMC 3.99,3.385 4.302,3.604 0.313,0.219 10 E2 0.542,4.76 3.958,4.969 3.417,0.208 10 VCM: Master Cylinder Pressure Sensor Power Supply 0.542,5.01 3.427,5.219 2.885,0.208 10 PMC: Master Cylinder Pressure Sensor Input 0.542,5.26 3.427,5.479 2.885,0.219 10 E2: Master Cylinder Pressure Sensor Ground

DTC No. Detection Item DTC Detection Condition Trouble Area
C1246 Master Cylinder Pressure Sensor Malfunction Any of the following is detected:
1.

The voltage of the sensor signal is out of range (below 0.129 V, above 3.29 V).

2.

An abnormality is detected in the skid control ECU internal sensor test.

3.

The sensor signal offset value is out of range.


·

Stop light switch circuit

·

Master cylinder pressure sensor circuit

·

Master cylinder pressure sensor (brake actuator assembly)



DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition - - - -
Malfunction Status The voltage of the sensor signal is out of range (below 0.129 V, above 3.29 V). ○ - -
An abnormality is detected in the skid control ECU internal sensor test. - ○ -
The sensor signal offset value is out of range. - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C367769E01
1.896,0.25 2.781,0.469 0.885,0.219 10 false form Battery 1.052,1.646 1.479,1.833 0.427,0.188 10 false STOP 1.823,1.385 1.958,1.563 0.135,0.177 10 false 7 2,1.615 2.135,1.792 0.135,0.177 10 false B 1.813,3.125 1.948,3.302 0.135,0.177 10 false 2 1.99,3.354 2.417,3.542 0.427,0.188 10 false GND 3.375,3.333 3.802,3.521 0.427,0.188 10 false OUT 3.583,1.25 3.719,1.427 0.135,0.177 10 false L 3.375,2.229 3.708,2.417 0.333,0.188 10 false ACC 1.969,3.75 2.396,3.938 0.427,0.188 10 false A45 1.958,3.896 3.74,4.104 1.781,0.208 10 false Stop Light Switch Assembly 0.646,4.365 2.427,4.573 1.781,0.208 10 false : Open Detection Area 3.75,1.021 3.917,1.208 0.167,0.188 10 false 3 3.75,2.031 3.917,2.219 0.167,0.188 10 false 4 3.75,3.115 3.917,3.302 0.167,0.188 10 false 1 5.281,1.021 5.469,1.208 0.188,0.188 10 false 42 5.281,2.021 5.469,2.208 0.188,0.188 10 false 10 5.281,3.115 5.469,3.302 0.188,0.188 10 false 44 5.542,1.115 5.948,1.302 0.406,0.188 10 false STP 5.542,2.115 5.948,2.302 0.406,0.188 10 false STPO 5.542,3.208 5.948,3.396 0.406,0.188 10 false STP2 5.385,3.927 5.813,4.115 0.427,0.188 10 false A42 5.385,4.073 6.917,4.448 1.531,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 4.125,4.177 4.958,4.552 0.833,0.375 10 false to Stop Light Circuit

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)

NG

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

2.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Master Cylinder Sensor Master cylinder pressure sensor reading Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 0.2 to 0.4 V Reading increases when brake pedal is depressed
Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display
Master Cylinder Sensor
50003 105 9

d.

Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the GTS changes when the brake pedal is depressed.

OK:

When the pedal is depressed, the voltage displayed on the GTS increases.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

3.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

B

C

3.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display
Stop Light SW
50003 105 37

d.

Check that the stop light switch display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
4.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle and depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1246 is not output. A
DTC C1246 is output. (for LHD) B
DTC C1246 is output. (for RHD) C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

C

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C360727C06
0.063,0.281 0.51,0.531 0.448,0.25 2.802,0.375 2.448,0.938 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.146,0.323 0.49,0.542 0.344,0.219 10 false A42 2.854,0.26 3.281,0.448 0.427,0.188 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-44 (STP2) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V*
A42-44 (STP2) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V


HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)