The skid control ECU (brake actuator assembly) receives stop light switch signals and uses them to determine whether or not the brakes are applied. DTCs may be stored if either of the following occurs:
Stop light switch stuck on malfunction.
The accelerator and brake pedals are depressed simultaneously.*
*: The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1249 | Open in Stop Light Switch Circuit | The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is depressed, the master cylinder pressure is 0.5 MPa (5.09 kgf/cm2, 72 psi) or less, and the stop light switch is on for 60 seconds or more. | ·
Wire harness or connector ·
Stop light switch assembly ·
Skid control ECU (brake actuator assembly) ·
Stop light circuit |
When replacing the skid control ECU (brake actuator assembly), perform system variant learning.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Interview the customer to check if the pedals were depressed simultaneously while driving or braking.
The pedals were not depressed simultaneously.
The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously.
If the pedals were depressed simultaneously, clear the DTC because it is not a malfunction.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the stop lights come on when the brake pedal is depressed.
| Result | Proceed to |
|---|---|
| All stop lights illuminate when the brake pedal is depressed and turn off when the brake pedal is released. | A |
| All stop lights do not illuminate when the brake pedal is depressed. | B |
| One or more stop lights illuminate when the brake pedal is depressed but remain on when the brake pedal is released. | C |
A
B
C
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Select the Data List using the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Tester Display |
|---|
| Stop Light SW |
Check that the stop light switch display observed on the GTS changes according to brake pedal operation.
The GTS displays ON or OFF according to brake pedal operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Stop Light Switch Assembly) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A45-1 (OUT) - Body ground | ·
Ignition switch to ON ·
The headlights are on ·
The blower motor switch is in the HI position ·
The rear window defogger is turned on ·
Stop light switch assembly off (Brake pedal released) |
1.5 V or less |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Clear the DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Start the engine.
Drive the vehicle and depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1249 is not output. | A |
| DTC C1249 is output. (for LHD) | B |
| DTC C1249 is output. (for RHD) | C |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Disconnect the A45 stop light switch assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A45-1 (OUT) - Body ground | Stop light switch assembly off
(Brake pedal released) |
1.5 V or less |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Disconnect the A42 skid control ECU (brake actuator assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A45-1 (OUT) - Body ground | Stop light switch assembly off
(Brake pedal released) |
1.5 V or less |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Check that there is no short to +B in the STP2 circuit (wire harnesses, connectors and stop lights).
No short to +B.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A42 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-44 (STP2) - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V* |
*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
A
B
C
Check that there is no open in the wire harnesses and connectors from terminal OUT of the stop light switch assembly to the stop lights.
No open.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Clear the DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT