Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2016.10–2019.09
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1434  Steering Angle Sensor Output Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the steering angle sensor via CAN communication.

HINT:

If there is a malfunction in the bus lines between the steering angle sensor and the CAN communication system, DTC U0126 (Lost Communication with Steering Angle Sensor Module) is output. When U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0126 first.


DTCs may be stored if one of the following occurs:

·

Steering angle sensor zero point value malfunction.

·

Steering angle sensor signal malfunction.

·

Steering angle sensor signal stuck malfunction.

·

Steering angle sensor and the yaw rate sensor values inconsistent.

·

Steering angle sensor installation abnormality.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1434 Steering Angle Sensor Output Malfunction Any of the following is detected:
1.

The difference between zero point stored in the steering angle sensor and the estimated zero point exceeds 15 deg.

2.

The offset value of the steering angle sensor is -13.5 deg. or less or 13.5 deg. or more.

3.

The steering angle sensor value exceeds a specified value for 0.3 seconds or more.

4.

The change of the steering angle sensor value within 0.02 seconds is abnormal.

5.

The steering angle sensor value changes by less than 5 deg. and both left and right turns have been recognized.

6.

There is a difference between the skid control ECU (brake actuator assembly) estimated value and the steering angle sensor value due to an abnormal steering angle sensor value.


·

Sensor installation

·

Steering angle sensor power supply

·

Steering angle sensor

·

Skid control ECU (brake actuator assembly)



DTC Detection Conditions: C1434
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition - - - -
Malfunction Status The difference between zero point stored in the steering angle sensor and the estimated zero point exceeds 15 deg. ○ - -
The offset value of the steering angle sensor is -13.5 deg. or less or 13.5 deg. or more. - ○ -
The steering angle sensor value exceeds a specified value. - - ○
Detection Time - - 0.3 seconds or more
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1434
Vehicle Condition
Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition - - - -
Malfunction Status The change of the steering angle sensor value within 0.02 seconds is abnormal. ○ - -
The steering angle sensor value changes by less than 5 deg. and both left and right turns have been recognized. - ○ -
There is a difference between the skid control ECU (brake actuator assembly) estimated value and the steering angle sensor value due to an abnormal steering angle sensor value. - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C367767E03
0.813,0.635 1.24,0.833 0.427,0.198 10 false CANL 0.792,1.24 1.219,1.438 0.427,0.198 10 false CANH 0.896,1.719 1.198,1.927 0.302,0.208 10 false BAT 0.958,2.396 1.26,2.604 0.302,0.208 10 false IG1 0.885,3.25 1.229,3.458 0.344,0.208 10 false ESS 0.115,4 0.406,4.198 0.292,0.198 10 false F69 0.104,4.167 1.51,4.396 1.406,0.229 10 false Steering Angle Sensor 1.281,0.5 1.417,0.708 0.135,0.208 10 false 2 1.281,1.094 1.417,1.302 0.135,0.208 10 false 3 1.281,1.615 1.417,1.823 0.135,0.208 10 false 5 1.281,2.313 1.417,2.521 0.135,0.208 10 false 4 1.26,3.198 1.396,3.406 0.135,0.208 10 false 1 2,1.896 3.083,2.083 1.083,0.188 10 false ECU-DCC NO. 1 1.979,2.563 3.063,2.75 1.083,0.188 10 false ECU-IG1 NO. 2 1.99,2.313 2.188,2.521 0.198,0.208 10 false *2 1.635,2.656 1.802,2.865 0.167,0.208 10 false *1 3.646,2.875 5.385,3.094 1.74,0.219 10 false from Stop and Start System 3.604,1.729 4.469,1.927 0.865,0.198 10 false from Battery 3.625,2.396 5.042,2.625 1.417,0.229 10 false from IG1-NO. 1 Relay 2.969,3.542 4.656,3.75 1.688,0.208 10 false : CAN Communication Line 2.313,3.979 4.188,4.219 1.875,0.24 10 false *1: w/ Stop and Start System 2.313,4.271 4.24,4.49 1.927,0.219 10 false *2: w/o Stop and Start System 5.594,3.969 5.885,4.177 0.292,0.208 10 false A42 5.594,4.125 7.135,4.51 1.542,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 5.771,0.479 5.969,0.667 0.198,0.188 10 false 19 5.833,1.083 5.969,1.271 0.135,0.188 10 false 5 6.042,0.656 6.469,0.854 0.427,0.198 10 false CANL 6.042,1.26 6.469,1.458 0.427,0.198 10 false CANH

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

When U0073, U0123, U0124 and/or U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0073, U0123, U0124 and/or U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073

·

When a speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, DTCs for the steering angle sensor may be stored even though the steering angle sensor is normal. When DTCs for a speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


d.

Start the engine.


e.

Drive the vehicle at a speed of 50 km/h (31 mph) and turn the steering wheel to the right and left and then check that no speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105
Result:
Result Proceed to
No CAN communication system, speed sensor, or yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output. A
CAN communication system DTCs are output. B
Speed sensor and/or yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output. C


HINT:
·

If a speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, DTCs for the steering angle sensor may be stored even though the steering angle sensor is normal.

·

If speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output simultaneously, repair these malfunctions and then inspect the steering angle sensor.





A

2.CHECK STEERING ANGLE SENSOR INSTALLATION

B

C

2.CHECK STEERING ANGLE SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the steering angle sensor has been installed properly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>INSTALLATION

OK:

The steering angle sensor installation is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C368478C01
0.198,1.052 0.583,1.333 0.385,0.281 1.917,2.563 2.573,2.073 true 2.115,2.708 2.469,2.958 true 0.177,0.177 0.49,0.375 0.313,0.198 10 false *a 0.271,1.104 0.583,1.302 0.313,0.198 10 false F69 2.635,1.99 2.948,2.188 0.313,0.198 10 false IG1 2.521,2.906 2.833,3.104 0.313,0.198 10 false BAT
*a Front view of wire harness connector
(to Steering Angle Sensor)


Remove the steering wheel and column cover.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the F69 steering angle sensor connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F69-5 (BAT) - Body ground Always 11 to 14 V
F69-4 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System for IG1 circuit) B
NG (w/ Stop and Start System for IG1 circuit) C



A

4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

C

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
C368478C02
0.177,1.146 0.615,1.406 0.438,0.26 0.875,2.948 1.344,2.688 true 0.229,0.156 0.542,0.354 0.313,0.198 10 false *a 0.281,1.198 0.688,1.479 0.406,0.281 10 false F69 0.563,2.896 0.969,3.177 0.406,0.281 10 false ESS
*a Front view of wire harness connector
(to Steering Angle Sensor)


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E69-1 (ESS) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)