Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM
RM32H0E _54 Brake _060043 PARKING BRAKE _0294919 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C1207  Gear Position Signal Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) detects shift position signal malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C1207 Gear Position Signal Malfunction Any of the following is detected:
·

Neutral position switch open or short circuit is detected for 0.1 seconds or more

·

Neutral position switch power supply voltage and +BS terminal voltage are judged to be abnormal for 0.1 seconds or more.


·

Neutral position switch

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition - - - -
Malfunction Status Neutral position switch open circuit is detected ○ - -
Neutral position switch short circuit is detected - ○ -
Neutral position switch power supply voltage and +BS terminal voltage are judged to be abnormal - - ○
Detection Time 0.1 seconds or more 0.1 seconds or more 0.1 seconds or more
Number of Trips 1 trip 1 trip 1 trip

WIRING DIAGRAM

C367781E07
0.958,2.094 1.271,2.292 0.313,0.198 10 false IC 2.323,1.104 2.646,1.344 0.323,0.24 10 false W1 2.26,1.979 2.635,2.156 0.375,0.177 10 false TMN 2.375,2.854 2.719,3.042 0.344,0.188 10 false F+ 2.677,1.094 2.906,1.271 0.229,0.177 10 false 1 2.688,1.979 2.917,2.156 0.229,0.177 10 false 2 2.688,2.854 2.917,3.031 0.229,0.177 10 false 3 0.75,3.49 1.219,3.677 0.469,0.188 10 false C61 0.76,3.646 2.427,3.875 1.667,0.229 10 false Neutral Position Switch 5.281,3.781 5.75,3.969 0.469,0.188 10 false A42 5.271,3.948 6.833,4.427 1.563,0.479 10 false Skid Control ECU (Brake Actuator Assembly) 4.854,1.104 5.083,1.281 0.229,0.177 10 false 27 4.875,1.979 5.104,2.156 0.229,0.177 10 false 45 4.885,2.865 5.115,3.042 0.229,0.177 10 false 29 5.167,1.208 5.708,1.417 0.542,0.208 10 false NVCC 5.167,2.094 5.708,2.302 0.542,0.208 10 false NSIG 5.167,2.979 5.708,3.188 0.542,0.208 10 false NGND

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light blinks (red) when the ignition switch is first turned to ON.



PROCEDURE

1.CHECK DTC
a.

Check for DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105

Result:
Result Proceed to
Only DTC C1207 is output A
DTCs C1207 and C1241 are output B
DTCs C1207 and C1417 are output C



A

2.CHECK SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) (TERMINAL VOLTAGE)

B

C

2.CHECK SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) (TERMINAL VOLTAGE)
a.

Disconnect the neutral position switch connector.


b.
C367820C06
1.417,0.25 1.917,0.5 0.5,0.25 1.188,1.635 1.51,1.167 true 2.229,1.646 1.823,1.177 true 1,1.667 1.313,1.865 0.313,0.198 10 false W1 2.198,1.688 2.51,1.885 0.313,0.198 10 false F+ 0.208,0.156 0.521,0.354 0.313,0.198 10 false *a 1.531,0.281 2.031,0.479 0.5,0.198 10 false C61
*a Front view of wire harness connector
(to Neutral Position Switch)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C61-1 (W) - C61-3 (F+) Ignition switch ON 4.5 to 5.5 V



Result:
Result Proceed to
OK A
NG B



A

3.INSPECT SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - NEUTRAL POSITION SWITCH)
3.INSPECT SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
a.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

C360725C10
3.313,0.083 3.813,0.333 0.5,0.25 3.417,1.458 3.094,0.833 true 2.594,0.323 2.854,0.688 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 3.438,0.125 3.802,0.302 0.365,0.177 10 false A42 2.24,0.177 2.854,0.375 0.615,0.198 10 false NSIG 3.458,1.417 4.188,1.625 0.729,0.208 10 false NVCC
*a Component with harness connected
(Skid Control ECU (Brake Actuator Assembly))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A42-27 (NVCC) - A42-45 (NSIG) Always 995 to 1005 Ω



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - NEUTRAL POSITION SWITCH)

B

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

C

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - NEUTRAL POSITION SWITCH)
a.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the C61 neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-45 (NSIG) - C61-2 (TMN) Always Below 1 Ω
A42-45 (NSIG) or C61-2 (TMN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SHORT TO B+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SHORT TO B+)
a.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the C61 neutral position switch connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-45 (NSIG) or C61-2 (TMN) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - NEUTRAL POSITION SWITCH)
a.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the C61 neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-27 (NVCC) - C61-1 (W1) Always Below 1 Ω
A42-29 (NGND) - C61-3 (F+) Always Below 1 Ω
A42-27 (NVCC) or C61-1 (W1) - Body ground and other terminals Always 10 kΩ or higher
A42-29 (NGND) or C61-3 (F+) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (SHORT TO B+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SHORT TO B+)
a.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the C61 neutral position switch connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-27 (NVCC) or C61-1 (W1) - Body ground Ignition switch ON Below 1 V
A42-29 (NGND) or C61-3 (F+) - Body ground Ignition switch ON Below 1 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR