Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › CAMSHAFT OIL CONTROL SOLENOID
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0295064 CAMSHAFT OIL CONTROL SOLENOID A

8NR-FTS ENGINE CONTROL  CAMSHAFT OIL CONTROL SOLENOID  REMOVAL  


PROCEDURE

Hide 1.REMOVE FRONT WHEEL RH

Hide 51441 2.REMOVE NO.1 ENGINE UNDER COVER

Hide 51443C 3.REMOVE REAR ENGINE UNDER COVER RH

Hide 4.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55737B 5.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55735A 6.REMOVE WATER GUARD PLATE LH

Hide 55736D 7.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 8.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 9.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 10.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 12305 13.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH (w/ Air Conditioning System)

a.
A395313

Remove the bolt and separate the No. 2 earth wire from the engine mounting insulator sub-assembly RH.


b.
A394701

Remove the bolt, nut and separate the air conditioner tube and accessory assembly from the vehicle and engine mounting insulator sub-assembly RH.

HINT:

This step is performed in order to remove the engine mounting insulator sub-assembly RH.



c.
A395314

Remove the 4 bolts, 2 nuts and engine mounting insulator sub-assembly RH from the vehicle and engine mounting bracket RH.

HINT:

As the engine mounting insulator sub-assembly RH contacts the air conditioning tube assembly and cannot be taken out, move the engine mounting insulator sub-assembly RH to a position where the bolt of the camshaft timing oil control solenoid assembly can be removed.



Hide 12305 14.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH (w/o Air Conditioning System)

a.
A396144

Remove the bolt and separate the No. 2 earth wire from the engine mounting insulator sub-assembly RH.


b.
A396145

Remove the 4 bolts, 2 nuts and engine mounting insulator sub-assembly RH from the vehicle and engine mounting bracket RH.


Hide 15370 15.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side)

a.
A392682

Disconnect the camshaft timing oil control solenoid assembly connector.


b.

Remove the 2 bolts and camshaft timing oil control solenoid assembly from the timing chain cover assembly.

NOTICE:

If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.



c.
A352636

Remove the O-ring from the camshaft timing oil control solenoid assembly.

NOTICE:
·

If the O-ring comes off in the timing chain cover assembly, make sure to remove it.

·

Do not drop the O-ring into the timing chain cover assembly.




Hide 15370 16.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side)

a.
A392688

Remove the bolt and separate the engine wire from the cylinder head cover sub-assembly.


b.
A392685

Disengage the clamp to remove the wire harness clamp bracket from the engine wire.


c.
A392689

Disconnect the camshaft timing oil control solenoid assembly connector.


d.

Remove the 2 bolts and camshaft timing oil control solenoid assembly from the timing chain cover assembly.

NOTICE:

If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.



e.
A352636

Remove the O-ring from the camshaft timing oil control solenoid assembly.

NOTICE:
·

If the O-ring comes off in the timing chain cover assembly, make sure to remove it.

·

Do not drop the O-ring into the timing chain cover assembly.