Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0295313 COMPRESSOR A

HEATING / AIR CONDITIONING  COMPRESSOR  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.
I112511

When replacing the compressor with pulley assembly with a new one, gradually discharge the refrigerant gas from the service valve. Then drain the following amount of oil from the new compressor with pulley assembly before installation, so that the amount of oil contained in it is the same as that in the cooler compressor with pulley assembly to be replaced.

Standard:

Standard: (The amount of oil inside a new cooler compressor with pulley assembly: 80 (+15) cc (2.82 (+0.51) fl.oz.)) - (The amount of oil remaining in the removed compressor with pulley assembly A + oil remaining in the reserve chamber B) = (The amount of oil to be removed when replacing the cooler compressor with pulley assembly)


HINT:

A new cooler compressor with pulley assembly is filled with sufficient oil for the whole cycle. Therefore, it is necessary to drain residual oil from the condenser and cooling unit. Example: If A is 20 cc (0.68 fl.oz.) and B is 25 cc (0.85 fl.oz.), A+B=45 cc (1.52 fl.oz.). Since this time 80 cc (2.82fl.oz.) - 45 cc (1.52 fl.oz.) =15 cc (0.51 fl.oz.), drain 15 cc (0.51 fl.oz.) of the oil from the new cooler compressor with pulley assembly.


NOTICE:
·

When A + B exceeds the standard oil fill volume specified for the compressor with pulley assembly by part number, install the compressor with pulley assembly without adjusting the oil volume. Example: If A is 40 cc (1.35 fl.oz.) and B is 25 cc (0.85 fl.oz.), A+B is greater than 80 cc (2.82 fl.oz.) and less than 95 cc (2.64 fl.oz.), so install the cooler compressor with pulley assembly as is.

·

When checking the compressor oil level, observe the precautions for cooler removal/installation.

·

If a new cooler compressor with pulley assembly is installed without removing the same amount of oil as is remaining in the vehicle pipes, the amount of oil will be too large. This prevents heat exchange in the refrigerant cycle and will cause a refrigeration failure.

·

If the amount of oil remaining in the removed compressor with pulley assembly is too low, check for an oil leak.

·

Use VC100YF or equivalent for compressor oil.(for VALEO Made)

·

Use ND-OIL 8 or equivalent for compressor oil.(for DENSO Made)




Hide 88310 2.INSTALL COMPRESSOR WITH PULLEY ASSEMBLY

a.

Using an E8 "TORX" socket wrench, temporarily install the compressor with pulley assembly with the 2 stud bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


b.
I112576E01
1.083,0.458 1.24,0.656 0.156,0.198 10 true 1 2.167,0.938 2.323,1.135 0.156,0.198 10 true 2 2.313,0 2.448,0.177 0.135,0.177 10 true 4 0.552,1.375 0.708,1.573 0.156,0.198 10 true 3

Temporarily install the 2 bolts and 2 nuts.


c.

Tighten the 2 bolts and 2 nuts to install the compressor with pulley assembly in the order as shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


d.

Connect the connector.


Hide 88704 3.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction hose sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with pulley assembly.

Compressor Oil:

for VALEO Made

VC100YF or equivalent

for DENSO Made

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction hose sub-assembly.


d.

Connect the suction hose sub-assembly to the compressor with pulley assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88703 4.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the discharge hose sub-assembly.


b.

Apply sufficient compressor oil to a new O-rings and fitting surfaces of the cooler compressor with pulley assembly.

Compressor Oil:

for VALEO Made

VC100YF or equivalent

for DENSO Made

ND-OIL 8 or equivalent



c.

Install the O-ring to the discharge hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the suction hose sub-assembly to the compressor with pulley assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 16361A 5.INSTALL FAN AND GENERATOR V BELT

Hide 51441 6.INSTALL NO. 1 ENGINE UNDER COVER

Hide 7.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for HFC-134a(R134a))

Hide 8.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for HFO-1234yf(R1234yf))

Hide 9.WARM UP WARM UP ENGINE (for HFC-134a(R134a))

Hide 10.WARM UP WARM UP ENGINE (for HFO-1234yf(R1234yf))

Hide 11.INSPECT FOR REFRIGERANT LEAK (for HFC-134a(R134a))

Hide 12.INSPECT FOR REFRIGERANT LEAK (for HFO-1234yf(R1234yf))