Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059427 STOP AND START _0295332 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P0562  System Voltage Low  


DESCRIPTION

The engine stop and start ECU monitors the +B terminal voltage while the engine is stopped by stop and start control. If the voltage drops below the specified level, the engine stop and start ECU stores DTC P0562 and blinks the stop and start cancel indicator light.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0562 System Voltage Low All of the following conditions are met for 2 seconds or more (1 trip detection logic):
·

+B terminal voltage is 9 V or less.

·

Engine stop by stopped and start control


·

Battery

·

Wire harness or connector

·

No. 1 integration relay (EFI-MAIN relay)

·

Engine stop and start ECU


Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



f.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Keep the engine stopped by stop and start control for 1 second or more.


h.

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.



i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A392126E01
0.708,1.271 1.875,1.469 1.167,0.198 10 false EFI-MAIN NO. 1 2.698,2.031 3.448,2.229 0.75,0.198 10 false EFI-MAIN 2.281,2.583 4.031,2.833 1.75,0.25 10 false No. 1 Integration Relay 0.688,3.104 1.604,3.271 0.917,0.167 10 false BATT-MAIN 2.958,3.823 3.458,3.99 0.5,0.167 10 false MREL 3.438,3.74 3.938,3.906 0.5,0.167 10 false 46 2.823,4.354 3.323,4.521 0.5,0.167 10 false A38 2.813,4.531 3.313,4.698 0.5,0.167 10 false ECM 0.844,4.375 1.427,4.625 0.583,0.25 10 false Battery 5.844,4.344 6.427,4.51 0.583,0.167 10 false A62 5.833,4.51 6.917,4.927 1.083,0.417 10 false Engine Stop and Start ECU 5.729,3.313 5.979,3.479 0.25,0.167 10 false 6 5.948,3.458 6.531,3.625 0.583,0.167 10 false DGND 5.927,1.125 6.51,1.292 0.583,0.167 10 false +B 5.729,1.021 5.896,1.188 0.167,0.167 10 false 1 4.542,1.281 5.458,1.448 0.917,0.167 10 false EFI NO. 3 2.271,2.417 2.583,2.615 0.313,0.198 10 false 1B 2.073,0.969 2.229,1.167 0.156,0.198 10 false 3 2.073,1.573 2.229,1.771 0.156,0.198 10 false 6 3.792,0.99 3.948,1.188 0.156,0.198 10 false 4 3.792,1.594 3.948,1.792 0.156,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA


PROCEDURE

1.READ VALUE USING GTS (BATTERY VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

HINT:

Do not start the engine.



c.

Turn the GTS on.


d.

Turn off all electrical systems.


e.

Enter the following menus: Powertrain / Stop and Start / Data List / Battery Voltage.

Powertrain > Stop and Start > Data List
Tester Display
Battery Voltage
50003 227 6

f.

Read the battery voltage displayed on the GTS screen.

Result:
Result Proceed to
9 to 14 V A
Below 9 V B




A

B

2.INSPECT NO. 1 INTEGRATION RELAY (EFI-MAIN)
2.INSPECT NO. 1 INTEGRATION RELAY (EFI-MAIN)
a.

Inspect the No. 1 integration relay.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (+B TERMINAL VOLTAGE)

NG

3.CHECK HARNESS AND CONNECTOR (+B TERMINAL VOLTAGE)
a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

A387803C11
1.948,0.083 2.448,0.333 0.5,0.25 3.167,0.083 3.667,0.333 0.5,0.25 4.604,0.083 5.104,0.333 0.5,0.25 4.417,1.51 4.083,0.844 true 0.135,0.073 0.448,0.229 0.313,0.156 10 false *a 2.073,0.125 2.531,0.323 0.458,0.198 10 false A61 3.281,0.125 3.74,0.323 0.458,0.198 10 false A62 4.729,0.125 5.188,0.323 0.458,0.198 10 false F77 4.344,1.542 4.958,1.74 0.615,0.198 10 false +B
*a Component with harness connected
(Engine Stop and Start ECU)
- -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
A62-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR