Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059427 STOP AND START _0295332 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P1541  Brake Booster Sensor Circuit  


DESCRIPTION

The engine stop and start ECU determines changes in the brake booster assembly pressure based on the voltage signal received from the vacuum sensor assembly in the brake booster assembly.

If the output value of the vacuum sensor assembly remains the same even though the brake booster assembly pressure changes when the brake pedal is operated or the vehicle is being driven, the engine stop and start ECU judges that the sensor is stuck.

When sticking of the sensor is detected, the engine stop and start ECU stores DTC P1541 and blinks the stop and start cancel indicator light.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1541 Brake Booster Sensor Circuit Any of the following conditions are met (1 trip detection logic):
·

The change in vacuum is 0.3 kPa or less more than 3 times when the brake pedal is firmly depressed to stop the vehicle (deceleration of 0.15 G or more for 1 second or more).

·

The change in vacuum while stopping the vehicle 30 times from a speed of 30 km/h (19 mph) or more was 0.3 kPa or less


·

Vacuum sensor assembly

·

Brake booster assembly

·

Check valve to connector tube hose (Brake booster hose)

·

Engine stop and start ECU


Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared automatically even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Enter the following menus: Powertrain / Stop and Start / Data List / Brake Boost Pressure.

Powertrain > Stop and Start > Data List
Tester Display
Brake Boost Pressure
50003 227 61

f.

Drive the vehicle at 30 km/h (19 mph) or more and stop the vehicle. Repeat this driving pattern 30 times to allow the brake booster vacuum to change.


g.

Stop the vehicle.


h.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


e.

Check for any other DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 227
Result:
Result Proceed to
DTC P1541 is output A
DTC P1541 and other DTCs output B




A

2.READ VALUE USING GTS (BRAKE BOOST PRESSURE)

B

2.READ VALUE USING GTS (BRAKE BOOST PRESSURE)
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Stop and Start / Data List / Brake Boost Pressure.


f.

Depress the brake pedal 5 times and read the changes in the following pressure value.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Normal Condition
Brake Boost Pressure Condition:
·

Ignition switch ON

·

Brake pedal depressed 5 times


Changes by 20 kPa (0.2 kgf/cm2, 2.9 psi) or higher
Powertrain > Stop and Start > Data List
Tester Display
Brake Boost Pressure
50003 227 61

Result:
Proceed to
OK
NG



OK

NG

3.INSPECT VACUUM HOSE ASSEMBLY (BRAKE BOOSTER HOSE)
3.INSPECT VACUUM HOSE ASSEMBLY (BRAKE BOOSTER HOSE)
a.

Check the vacuum hose assembly (brake booster hose) for cracks or clogging (visual check).

HINT:

If the braking force is abnormal, inspect the brake booster assembly.


OK:

No cracks or clogging in the vacuum hose assembly (brake booster hose).



Result:
Proceed to
OK
NG



OK

4.REPLACE VACUUM SENSOR ASSEMBLY

NG

REPLACE VACUUM HOSE ASSEMBLY

4.REPLACE VACUUM SENSOR ASSEMBLY
a.

Replace the vacuum sensor assembly.

Click hereEngine / Hybrid System>STOP AND START>VACUUM SENSOR ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


e.

Clear the DTC.

Powertrain > Stop and Start > Clear DTCs
50002 227

Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Start the engine and warm it up.


b.

Turn the GTS on.


c.

Enter the following menus: Powertrain / Stop and Start / Data List / Brake Boost Pressure.

Powertrain > Stop and Start > Data List
Tester Display
Brake Boost Pressure
50003 227 61

d.

Drive the vehicle at 30 km/h (19 mph) or more and stop the vehicle. Repeat this driving pattern 30 times to allow the brake booster vacuum to change.


e.

Stop the vehicle.


f.

Check that no DTCs are output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227
Result:
Result Proceed to
DTCs are not output A
DTC P1541 is output B




A

END

B