Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) › 2016.10–2019.09
RM32H0E _56 Audio / Visual / Telematics _060227 AUDIO / VIDEO _0295448 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

w/o Manual (SOS) Switch

The radio receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio receiver assembly.


w/ Manual (SOS) Switch

The radio receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the telematics transceiver sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio receiver assembly via the telematics transceiver.


WIRING DIAGRAM

E345611E02
0.156,0.115 3.823,0.313 3.667,0.198 12 false w/o Manual (SOS) Switch: 0.167,4.5 3.833,4.698 3.667,0.198 12 false w/ Manual (SOS) Switch: 0.813,0.792 1.427,0.99 0.615,0.198 10 false MACC 0.823,1.271 1.438,1.469 0.615,0.198 10 false MCO+ 0.823,1.719 1.438,1.917 0.615,0.198 10 false MCO- 0.833,2.719 1.448,2.917 0.615,0.198 10 false SNS2 3.25,2.073 4.115,2.313 0.865,0.24 10 false (Shielded) 1.313,0.698 1.927,0.896 0.615,0.198 10 false 9 1.313,1.177 1.927,1.375 0.615,0.198 10 false 8 1.313,1.646 1.927,1.844 0.615,0.198 10 false 7 1.313,2.604 1.927,2.802 0.615,0.198 10 false 1 5.75,0.688 6.365,0.885 0.615,0.198 10 false 4 5.74,1.177 6.354,1.375 0.615,0.198 10 false 5 5.719,1.583 6.333,1.781 0.615,0.198 10 false 19 5.698,2.104 6.313,2.302 0.615,0.198 10 false 18 5.75,4.979 6.365,5.177 0.615,0.198 10 false 6 5.969,0.802 6.583,1 0.615,0.198 10 false MACC 5.969,1.24 6.583,1.438 0.615,0.198 10 false MIN+ 5.969,1.729 6.583,1.927 0.615,0.198 10 false MIN- 5.969,2.198 6.583,2.396 0.615,0.198 10 false SGND 5.969,2.688 6.583,2.885 0.615,0.198 10 false SNS2 0.229,3.156 0.844,3.354 0.615,0.198 10 false R2 5.76,3.188 6.375,3.385 0.615,0.198 10 false F47 5.792,3.385 6.74,3.823 0.948,0.438 10 false Radio Receiver Assembly 0.833,5.094 1.448,5.292 0.615,0.198 10 false SNS2 0.833,5.583 1.448,5.781 0.615,0.198 10 false MACC 0.854,6.083 1.469,6.281 0.615,0.198 10 false MCO+ 0.844,6.542 1.458,6.74 0.615,0.198 10 false MCO- 3.24,5.49 3.854,5.688 0.615,0.198 10 false 33 1.323,5.479 1.938,5.677 0.615,0.198 10 false 9 1.333,5.958 1.948,6.156 0.615,0.198 10 false 8 1.333,6.438 1.948,6.635 0.615,0.198 10 false 7 2.073,6.875 2.938,7.115 0.865,0.24 10 false (Shielded) 3.479,5.604 4.094,5.802 0.615,0.198 10 false MCVD 3.5,6.052 4.115,6.25 0.615,0.198 10 false MCI+ 3.5,6.5 4.115,6.698 0.615,0.198 10 false MCI- 3.49,6.979 4.104,7.177 0.615,0.198 10 false SGND 4.802,6.875 5.667,7.115 0.865,0.24 10 false (Shielded) 5.99,5.094 6.604,5.292 0.615,0.198 10 false SNS2 5.979,6.042 6.594,6.24 0.615,0.198 10 false MIN+ 5.99,6.521 6.604,6.719 0.615,0.198 10 false MIN- 5.958,7.021 6.573,7.219 0.615,0.198 10 false SGND 0.219,7.406 0.833,7.604 0.615,0.198 10 false R2 0.229,3.354 2.281,3.833 2.052,0.479 10 false Map Light Assembly (Telephone Microphone Assembly) 0.208,7.594 2.26,8.073 2.052,0.479 10 false Map Light Assembly (Telephone Microphone Assembly) 5.802,7.427 6.417,7.625 0.615,0.198 10 false F47 5.813,7.625 6.792,8.021 0.979,0.396 10 false Radio Receiver Assembly 3.271,7.396 3.885,7.594 0.615,0.198 10 false F51 3.26,7.583 5.01,7.844 1.75,0.26 10 false Telematics Transceiver 3.24,5.948 4.031,6.115 0.792,0.167 10 false 34 3.24,6.427 4.031,6.594 0.792,0.167 10 false 35 3.26,6.885 4.052,7.052 0.792,0.167 10 false 32 5.771,5.938 6.385,6.135 0.615,0.198 10 false 5 5.719,6.417 6.333,6.615 0.615,0.198 10 false 19 5.729,6.885 6.344,7.083 0.615,0.198 10 false 18 5.74,2.604 6.354,2.802 0.615,0.198 10 false 6 1.333,4.969 1.948,5.167 0.615,0.198 10 false 1 3.969,6.5 4.583,6.698 0.615,0.198 10 false MCO- 3.969,6.063 4.583,6.26 0.615,0.198 10 false MCO+ 4.448,5.958 5.063,6.156 0.615,0.198 10 false 18 4.448,6.417 5.063,6.615 0.615,0.198 10 false 19

PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
w/o Manual (SOS) Switch A
w/ Manual (SOS) Switch B




A

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

B

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F47 radio receiver assembly connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F47-6 (SNS2) - R2-1 (SNS2) Always Below 1 Ω
F47-4 (MACC) - R2-9 (MACC) Always Below 1 Ω
F47-5 (MIN+) - R2-8 (MCO+) Always Below 1 Ω
F47-19 (MIN-) - R2-7 (MCO-) Always Below 1 Ω
F47-6 (SNS2) or R2-1 (SNS2) - Body ground Always 10 kΩ or higher
F47-4 (MACC) or R2-9 (MACC) - Body ground Always 10 kΩ or higher
F47-5 (MIN+) or R2-8 (MCO+) - Body ground Always 10 kΩ or higher
F47-19 (MIN-) or R2-7 (MCO-) - Body ground Always 10 kΩ or higher
F47-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO RECEIVER ASSEMBLY
a.

Connect the F47 radio receiver assembly connector.


b.

Connect the R2 map light assembly (telephone microphone assembly) connector.


c.
E359760C01
1.427,0.625 1.896,0.917 0.469,0.292 1.115,2.635 2.052,1.99 true 2.24,1.75 2.917,1.344 true 2.219,2 2.635,2.563 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 1.542,0.688 1.854,0.885 0.313,0.198 10 false F47 2.938,1.167 3.427,1.479 0.49,0.313 10 false MACC 2.594,2.625 3.052,2.875 0.458,0.25 10 false SGND 0.865,2.625 1.25,2.844 0.385,0.219 10 false MIN-
*a Component with harness connected
(Radio Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F47-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F47-18 (SGND) - Body ground Always Below 1 Ω
F47-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E358190C01
2.281,1.094 2.552,0.49 true 2.292,1.427 2.583,1.771 true 0.25,0.198 0.563,0.396 0.313,0.198 10 false *a 2.479,0.302 2.948,0.521 0.469,0.219 10 false SNS2 2.583,1.771 2.979,1.979 0.396,0.208 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Connect the R2 map light assembly (telephone microphone assembly) connector.


b.

Turn the ignition switch to ACC.


c.
E358189C01
1.542,0.49 1.969,0.75 0.427,0.26 2.188,1.75 2.708,2.177 true 1.99,1.781 2.208,2.385 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 1.646,0.521 1.958,0.719 0.313,0.198 10 false R2 2.76,2.188 3.198,2.458 0.438,0.271 10 false MCO- 2.115,2.427 2.604,2.698 0.49,0.271 10 false MCO+
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the R2 map light assembly (telephone microphone assembly) connector.


d.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B




A

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F47 radio receiver assembly connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F47-6 (SNS2) - R2-1 (SNS2) Always Below 1 Ω
F47-6 (SNS2) or R2-1 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F51 telematics transceiver connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F51-33 (MCVD) - R2-9 (MACC) Always Below 1 Ω
F51-34 (MCI+) - R2-8 (MIC+) Always Below 1 Ω
F51-35 (MCI-) - R2-7 (MIC-) Always Below 1 Ω
F51-33 (MCVD) or R2-9 (MACC) - Body ground Always 10 kΩ or higher
F51-34 (MCI+) or R2-8 (MIC+) - Body ground Always 10 kΩ or higher
F51-35 (MCI-) or R2-7 (MIC-) - Body ground Always 10 kΩ or higher
F51-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the F47 radio receiver assembly connector.


b.

Disconnect the F51 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F47-5 (MIN+) - F51-18 (MCO+) Always Below 1 Ω
F47-19 (MIN-) - F51-19 (MCO-) Always Below 1 Ω
F47-5 (MIN+) or F51-18 (MCO+) - Body ground Always 10 kΩ or higher
F47-19 (MIN-) or F51-19 (MCO-) - Body ground Always 10 kΩ or higher
F47-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT RADIO RECEIVER ASSEMBLY
a.

Connect the F47 radio receiver assembly connector.


b.

Disconnect the F51 telematics transceiver connector.


c.
E289390C45
1.521,0.698 1.896,0.938 0.375,0.24 2.635,2.625 2.229,1.99 true 2.063,2.771 2.063,1.969 true 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.583,0.729 2.073,0.896 0.49,0.167 10 false F47 2.604,2.667 3.125,2.875 0.521,0.208 10 false SGND 2.01,2.802 2.531,3.01 0.521,0.208 10 false MIN-
*a Component with harness connected
(Radio Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F47-18 (SGND) - Body ground Always Below 1 Ω
F47-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.INSPECT TELEMATICS TRANSCEIVER

NG

10.INSPECT TELEMATICS TRANSCEIVER
a.

Reconnect the F51 telematics transceiver connector.


b.
E259127C50
1.479,0.708 1.917,0.979 0.438,0.271 0.573,2.719 1.177,2.094 true 1.188,2.729 1.385,2.094 true 1.99,2.74 1.49,2.094 true 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 1.573,0.76 2.042,0.979 0.469,0.219 10 false F51 0.302,2.74 0.719,2.906 0.417,0.167 10 false MCI- 0.833,2.781 1.333,2.948 0.5,0.167 10 false MCVD 1.99,2.771 2.49,2.938 0.5,0.167 10 false SGND
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F51-33 (MCVD) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F51-32 (SGND) - Body ground Always Below 1 Ω
F51-35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

11.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E358190C02
2.281,1.094 2.552,0.49 true 2.292,1.427 2.583,1.771 true 0.25,0.198 0.563,0.396 0.313,0.198 10 false *a 2.479,0.302 2.948,0.521 0.469,0.219 10 false SNS2 2.583,1.771 2.979,1.979 0.396,0.208 10 false MIC-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS2) - 7 (MIC-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY

12.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the F47 radio receiver assembly connector.


b.

Reconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Reconnect the F51 telematics transceiver connector.


d.

Turn the ignition switch to ACC.


e.
E358189C02
1.542,0.49 1.969,0.75 0.427,0.26 2.188,1.75 2.708,2.177 true 1.99,1.781 2.208,2.385 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 1.646,0.521 1.958,0.719 0.313,0.198 10 false R2 2.76,2.188 3.198,2.458 0.438,0.271 10 false MCO- 2.115,2.427 2.604,2.698 0.49,0.271 10 false MCO+
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the R2 map light assembly (telephone microphone assembly) connector.


f.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B




A

B

REPLACE MAP LIGHT ASSEMBLY