Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM
RM32H0E _59 Vehicle Exterior _060314 WINDOW / GLASS _0295741 WINDOW DEFOGGER SYSTEM J

WINDOW / GLASS  WINDOW DEFOGGER SYSTEM  Rear Window Defogger System does not Operate  


DESCRIPTION

When the rear window defogger switch on the air conditioning control assembly is pressed, the operation signal is transmitted to the air conditioning amplifier assembly via LIN communication. When the air conditioning amplifier assembly receives the signal, it turns on the DEF relay to operate the window defogger system.

WIRING DIAGRAM

E358488E01
0.073,1.313 1.396,1.615 1.323,0.302 10 false from IG1 No. 1 Relay 0.594,2.469 1.417,2.677 0.823,0.208 10 false from Battery 2.021,1.469 3.094,1.677 1.073,0.208 10 false ECU-IG1 NO. 4 4.021,2.813 4.479,3 0.458,0.188 10 false DEF 2.344,3.99 3.813,4.417 1.469,0.427 10 false Back Door Glass (Rear Window Defogger Wire) 0.271,4.458 3.083,4.854 2.813,0.396 10 false *1: for TMMT Made 0.26,4.854 1.583,5.156 1.323,0.302 10 false *2: for TMC Made 0.729,5.344 2.688,5.552 1.958,0.208 10 false : LIN Communication Line 5.354,5 6.927,5.448 1.573,0.448 10 false Air Conditioning Amplifier Assembly 2.333,2.646 2.792,2.833 0.458,0.188 10 false DEF 5.573,1.323 6.031,1.51 0.458,0.188 10 false IG+ 5.573,2.083 6.031,2.271 0.458,0.188 10 false RDFG 5.573,4.573 6.031,4.76 0.458,0.188 10 false GND 5.573,0.375 6.031,0.563 0.458,0.188 10 false LIN1 3.563,0.375 4.021,0.563 0.458,0.188 10 false LIN1 4.813,0.385 5.271,0.573 0.458,0.188 10 false F72 4.792,1.333 5.25,1.521 0.458,0.188 10 false F72 4.802,2.104 5.26,2.292 0.458,0.188 10 false F72 4.802,4.594 5.26,4.781 0.458,0.188 10 false F72 5.208,0.385 5.667,0.573 0.458,0.188 10 false F73 5.208,1.333 5.667,1.521 0.458,0.188 10 false F73 5.208,2.104 5.667,2.292 0.458,0.188 10 false F73 5.208,4.594 5.667,4.781 0.458,0.188 10 false F73 2.281,3.646 2.74,3.833 0.458,0.188 10 false S14 3.594,3.646 4.052,3.833 0.458,0.188 10 false S13 3.969,0.198 4.198,0.427 0.229,0.229 10 false 2 4.885,0.177 5.115,0.406 0.229,0.229 10 false 3 5.24,0.188 5.469,0.417 0.229,0.229 10 false 14 4.865,1.135 5.094,1.365 0.229,0.229 10 false 5 5.271,1.135 5.5,1.365 0.229,0.229 10 false 2 4.854,1.896 5.083,2.125 0.229,0.229 10 false 26 5.292,1.896 5.521,2.125 0.229,0.229 10 false 5 4.854,4.385 5.083,4.615 0.229,0.229 10 false 29 5.292,4.385 5.521,4.615 0.229,0.229 10 false 4 4.833,0.573 5.063,0.802 0.229,0.229 10 false *1 5.229,0.573 5.458,0.802 0.229,0.229 10 false *2 4.844,1.521 5.073,1.75 0.229,0.229 10 false *1 5.24,1.521 5.469,1.75 0.229,0.229 10 false *2 4.844,2.292 5.073,2.521 0.229,0.229 10 false *1 4.833,4.771 5.063,5 0.229,0.229 10 false *1 5.229,2.292 5.458,2.521 0.229,0.229 10 false *2 5.24,4.781 5.469,5.01 0.229,0.229 10 false *2 2.656,0.854 4.813,1.063 2.156,0.208 10 false Air Conditioning Control Assembly 2.646,0.719 3.104,0.906 0.458,0.188 10 false F61 3.708,1.99 3.938,2.219 0.229,0.229 10 false 1 4.479,1.99 4.708,2.219 0.229,0.229 10 false 2 3.708,2.396 3.938,2.625 0.229,0.229 10 false 5 4.49,2.396 4.719,2.625 0.229,0.229 10 false 3 2.042,2.229 4.031,2.427 1.99,0.198 10 false ECU-IG1 NO. 3 0.083,2.073 3.146,2.271 3.063,0.198 10 false from IG1 NO. 1 Relay 3.667,3.427 3.823,3.625 0.156,0.198 10 false 1 2.344,3.427 2.5,3.625 0.156,0.198 10 false 1 3.01,0.417 3.469,0.604 0.458,0.188 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the battery voltage becomes low, window defogger system operation is canceled to prioritize supplying power to the power steering system.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DATA LIST / ACTIVE TEST



PROCEDURE

1.CHECK AIR CONDITIONING SYSTEM
a.

Check the air conditioning system.

HINT:

Both the window defogger system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly via the same communication line.


OK:

The air conditioning system operates normally.



Result:
Result Proceed to
OK A
NG (for Automatic Air Conditioning System with Top-mounted Air Conditioner Pressure Sensor) B
NG (for Automatic Air Conditioning System with Side-mounted Air Conditioner Pressure Sensor) C
NG (for Manual Air Conditioning System) D



A

2.PERFORM ACTIVE TEST USING GTS

B

C

D

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the Ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Defogger Relay (Rear) Rear window defogger wire OFF or ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
Defogger Relay (Rear)
50004 121 22
OK:

The window defogger system operates normally.



Result:
Proceed to
OK
NG



OK

3.REPLACE AIR CONDITIONING CONTROL ASSEMBLY

NG

4.INSPECT DEF RELAY
3.REPLACE AIR CONDITIONING CONTROL ASSEMBLY
a.

Replace the air conditioning control assembly with a new or known good one.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL>REMOVAL


b.

Check that the window defogger system operates normally.

Click hereVehicle Exterior>WINDOW / GLASS>WINDOW DEFOGGER SYSTEM>OPERATION CHECK

OK:

The window defogger system operates normally.



Result:
Proceed to
OK
NG



OK

END (AIR CONDITIONING CONTROL ASSEMBLY WAS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

4.INSPECT DEF RELAY
a.

Remove the DEF relay from the No. 1 engine room relay block.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (DEF RELAY - IG1 NO. 1 RELAY AND BATTERY)

NG

REPLACE DEF RELAY

5.CHECK HARNESS AND CONNECTOR (DEF RELAY - IG1 NO. 1 RELAY AND BATTERY)
a.
B462678C04
0.688,2.26 1,2.458 0.313,0.198 10 false *a 0.063,0.042 0.375,0.24 0.313,0.198 10 false *1
*1 No. 1 Engine Room Relay Block
*a DEF Relay Holder


Remove the DEF relay from the No. 1 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DEF relay holder terminal-1 - Body ground Ignition switch to ON 11 to 14 V
DEF relay holder terminal-5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (DEF RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (DEF RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

for TMMT Made

i.
B462678C05
0.094,0.094 0.406,0.292 0.313,0.198 10 false *1 0.688,2.26 1,2.458 0.313,0.198 10 false *a
*1 No. 1 Engine Room Relay Block
*a DEF Relay Holder


Disconnect the F72 air conditioning amplifier assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DEF relay holder terminal-2 - F72-26 (RDFG) Always Below 1 Ω
DEF relay holder terminal-2 or F72-26 (RDFG) - Body ground Always 10 kΩ or higher




b.

for TMC Made

i.

Disconnect the F73 air conditioning amplifier assembly.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Defogger relay holder terminal-2 - F73-5 (RDFG) Always Below 1 Ω
Defogger relay holder terminal-2 - F73-5 (RDFG) Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

7.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
B462683C02
0.875,1.01 1.198,1.24 0.323,0.229 1.542,2.344 1.302,1.792 true 0.708,2.354 1.146,1.802 true 0.927,1.031 1.385,1.229 0.458,0.198 10 false F72 1.385,2.375 2,2.573 0.615,0.198 10 false RDFG 0.542,2.375 1,2.573 0.458,0.198 10 false GND 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


for TMMT Made

i.

Reconnect the F72 air conditioning amplifier assembly connector.


ii.

Reinstall the defogger relay.


iii.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL


iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F72-26 (RDFG) - F72-29 (GND) Ignition switch ON, rear window defogger switch on Below 1 V
F72-26 (RDFG) - F72-29 (GND) Ignition switch ON, rear window defogger switch off 11 to 14 V




b.
B429629C11
1.552,0.302 1.917,0.563 0.365,0.26 1.229,1.771 1.375,1.083 true 2.385,1.74 2.198,1.188 true 1.625,0.344 2.083,0.542 0.458,0.198 10 false F73 2.219,1.781 2.833,1.979 0.615,0.198 10 false RDFG 1.063,1.792 1.521,1.99 0.458,0.198 10 false GND 0.052,0.052 0.365,0.25 0.313,0.198 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


for TMC Made

i.

Reconnect the F73 air conditioning amplifier assembly connector.


ii.

Reinstall the defogger relay.


iii.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL


iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F73-5 (RDFG) - F73-4 (GND) Ignition switch ON, rear window defogger switch on Below 1 V
F73-5 (RDFG) - F73-4 (GND) Ignition switch ON, rear window defogger switch off 11 to 14 V




Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS (REAR WINDOW DEFOGGER WIRE) - DEF RELAY AND BODY GROUND)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS (REAR WINDOW DEFOGGER WIRE) - DEF RELAY AND BODY GROUND)
a.
B462678C06
0.688,2.24 1,2.438 0.313,0.198 10 false *a 0.083,0.052 0.396,0.25 0.313,0.198 10 false *1
*1 NO. 1 Engine Room Relay Block
*a Defogger Relay Holder


Disconnect the S13 and S14 back door glass (rear window defogger wire) connectors.


b.

Remove the defogger relay from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S13-1 - Defogger relay holder terminal-3 Always Below 1 Ω
S14-1 - Body ground Always Below 1 Ω
S13-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE BACK DOOR GLASS (REAR WINDOW DEFOGGER WIRE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR