Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Hold Standby Indicator Light Circuit  


DESCRIPTION

When the brake hold switch (electric parking brake switch assembly) is turned on with the ignition switch turned to ON, the brake hold standby indicator light illuminates when brake hold operation is possible.

WIRING DIAGRAM

C367780E01
0.885,0.917 1.5,1.115 0.615,0.198 10 false CANL 0.875,1.729 1.49,1.927 0.615,0.198 10 false CANH 5.375,0.917 5.99,1.115 0.615,0.198 10 false CANL 5.375,1.729 5.99,1.927 0.615,0.198 10 false CANH 5.375,2.865 5.99,3.063 0.615,0.198 10 false HZRI 2.958,3.063 3.573,3.26 0.615,0.198 10 false F67 2.958,3.229 5.198,3.677 2.24,0.448 10 false Brake Hold Switch (Electric Parking Brake Switch Assembly) 3.635,2.76 4.25,2.958 0.615,0.198 10 false 8 3.865,3 4.479,3.198 0.615,0.198 10 false E 4.396,3 5.01,3.198 0.615,0.198 10 false +B 4.74,2.76 5.354,2.958 0.615,0.198 10 false 12 5.063,2.76 5.677,2.958 0.615,0.198 10 false 43 0.042,4.063 1.906,4.521 1.865,0.458 10 false Combination Meter Assembly (Meter Circuit Plate) 0.042,3.906 0.656,4.104 0.615,0.198 10 false F4 1.417,0.75 2.031,0.948 0.615,0.198 10 false 31 1.417,1.563 2.031,1.76 0.615,0.198 10 false 32 5.135,1.563 5.75,1.76 0.615,0.198 10 false 5 5.063,0.75 5.677,0.948 0.615,0.198 10 false 19 5.281,4.083 6.865,4.563 1.583,0.479 10 false Skid Control ECU (Brake Actuator Assembly) 5.292,3.917 5.906,4.115 0.615,0.198 10 false A42 2.938,4.344 4.802,4.615 1.865,0.271 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

HINT:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.PRE-CHECK
a.

If the brake hold standby indicator light does not illuminate even though the brake hold switch (electric parking brake switch assembly) is pushed, check that the brake hold function operation conditions are met.

1.

The driver's door is closed.

2.

Driver's seat belt is fastened.

3.

The engine hood is closed.

4.

The back door is closed.

5.

The system is normal.


Result:
Proceed to
NEXT




NEXT

2.CHECK CAN COMMUNICATION SYSTEM
2.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

3.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

3.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Jiggle the skid control ECU (brake actuator assembly) connectors and wire harnesses vertically and horizontally and check the brake hold standby indicator light status.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

4.INSPECT COMBINATION METER ASSEMBLY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

4.INSPECT COMBINATION METER ASSEMBLY
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch off.


c.

Perform the Active Test of the combination meter assembly using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Brake Hold
50004 122 72

d.

Check the combination meter assembly.

OK:

The brake hold standby indicator light turns on or off in accordance with the GTS operation.



Result:
Proceed to
OK
NG



OK

5.PERFORM ACTIVE TEST USING GTS (BRAKE HOLD STANDBY INDICATOR LIGHT)

NG

5.PERFORM ACTIVE TEST USING GTS (BRAKE HOLD STANDBY INDICATOR LIGHT)
a.

Turn the ignition switch to ON.


b.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
BH Standby Light Brake hold standby indicator light Indicator light ON/OFF Observe combination meter

c.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
BH Standby Light Brake hold standby indicator light ON or OFF ON: Indicator light on
OFF: Indicator light off
-
Chassis > ABS/VSC/TRC/EPB > Active Test
Active Test Display
BH Standby Light
Data List Display
BH Standby Light
50004 105 73 280

d.

Check the operating condition of the brake hold standby indicator light when operating it using the GTS.

Result:
Result Proceed to
Brake hold standby indicator light in the Data List does not change using the Active Test. (for LHD) A
Brake hold standby indicator light in the Data List does not change using the Active Test. (for RHD) B
Brake hold standby indicator light in the Data List turns ON/OFF using the Active Test. C




A

B

C

6.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY
6.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY
a.

Inspect the electric parking brake switch assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-43 (HZRI) - F67-12 (+B) Always Below 1 Ω
A42-43 (HZRI) or F67-12 (+B) - Body ground Always 10 kΩ or higher
F67-8 (E) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR