Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM32H0E _56 Audio / Visual / Telematics _060571 PARK ASSIST / MONITORING _0297206 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AC2  Slave Module Horizontal Axis Misalignment  


DESCRIPTION

This DTC is stored when the angle of the blind spot monitor sensor RH (Slave) deviates more than the allowable range from the horizontal axis.

HINT:
·

If a drum tester such as a speedometer tester, brake/speedometer combination tester or chassis dynamometer is used with the blind spot monitor system on, the blind spot monitor sensor may store this DTC by mistake.

·

When mud, snow, ice, a sticker, etc. is covering the sensor or its surrounding area on the rear bumper, the blind spot monitor sensor may store this DTC by mistake.



DTC No. Detection Item DTC Detection Condition Trouble Area
C1AC2 Slave Module Horizontal Axis Misalignment When the blind spot monitor sensor deviates 5 degrees or more from the horizontal axis when the system is activated Blind spot monitor sensor RH (Slave)

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor system is turned on.

·

If the bumper is damaged or the vehicle has a history of body repair, there is a possibility that the installation area of the blind spot monitor sensor may be deformed and the blind spot monitor sensor system may not operate correctly, so visually inspect the blind spot monitor sensor installation area (frame, stud bolt) to make sure it is not dented or bent.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK

If the visual inspection finds a problem, check the installation condition of the blind spot monitor sensor, and adjust the installation position of the blind spot monitor sensor as necessary.



PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Check the condition of the rear bumper around the blind spot monitor sensors.

HINT:

When mud, snow, ice, a sticker, etc. is covering the sensor or its surrounding area on the rear bumper, the blind spot monitor sensor may store this DTC by mistake.


Result:
Result Proceed to
A sticker, mud, snow, ice, etc. is covering the sensor or surrounding area on the rear bumper. A
There are scratches or dents on the rear bumper around the sensors. B
No abnormalities.




A

2.PERFORM BEAM AXIS CONFIRMATION

B

3.CHECK INSTALLATION CONDITION
2.PERFORM BEAM AXIS CONFIRMATION
a.

Clean the rear bumper.


b.

Perform Blind Spot Monitor Beam Axis Confirmation using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK

Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Display
50005 314 4239
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Adjustment
50005 314 4232

Result:
Proceed to
OK
NG



OK

END

NG

REPLACE BLIND SPOT MONITOR SENSOR RH (SLAVE)

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SENSOR>REMOVAL

NOTICE:

Before replacing the blind spot monitor sensor RH (Slave), visually check for damage to the stud bolts or area surrounding the blind spot monitor sensor RH (Slave).

If there is any damage to the stud bolts or area surrounding the blind spot monitor sensor RH (Slave), perform Blind Spot Monitor Sensor Installation Condition Inspection and adjust according to the result.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK



3.CHECK INSTALLATION CONDITION
a.

Check the installation condition of the blind spot monitor sensor RH (Slave).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK

HINT:

Take the appropriate action in accordance with the result.



Result:
Proceed to
NEXT



NEXT

4.PERFORM BEAM AXIS CONFIRMATION
4.PERFORM BEAM AXIS CONFIRMATION

b.

Perform Blind Spot Monitor Beam Axis Confirmation using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK

Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Display
50005 314 4239
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Adjustment
50005 314 4232

Result:
Proceed to
OK
NG



OK

END

NG