Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2016.10–2019.09
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU assembly is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the TRC OFF indicator light*1, TRC OFF message will be displayed on the multi-information display*2 and the VSC OFF indicator light will come on.

*1: for Color TFT Type

*2: for Monochrome TFT Type


WIRING DIAGRAM

C367780E02
0.885,0.917 1.5,1.115 0.615,0.198 10 false CANL 0.875,1.729 1.49,1.927 0.615,0.198 10 false CANH 5.375,0.917 5.99,1.115 0.615,0.198 10 false CANL 5.375,1.729 5.99,1.927 0.615,0.198 10 false CANH 5.375,2.865 5.99,3.063 0.615,0.198 10 false CSW 2.958,3.063 3.573,3.26 0.615,0.198 10 false F67 2.958,3.229 5.094,3.625 2.135,0.396 10 false VSC OFF Switch (Electric Parking Brake Switch Assembly) 3.635,2.76 4.25,2.958 0.615,0.198 10 false 8 3.865,3 4.479,3.198 0.615,0.198 10 false E 4.49,3 5.104,3.198 0.615,0.198 10 false + 4.74,2.76 5.354,2.958 0.615,0.198 10 false 11*2 5.135,2.76 5.75,2.958 0.615,0.198 10 false 6 0.042,4.063 1.906,4.521 1.865,0.458 10 false Combination Meter Assembly (Meter Circuit Plate) 0.042,3.906 0.656,4.104 0.615,0.198 10 false F4 1.417,0.75 2.031,0.948 0.615,0.198 10 false 31 1.417,1.563 2.031,1.76 0.615,0.198 10 false 32 5.135,1.563 5.75,1.76 0.615,0.198 10 false 5 5.063,0.75 5.677,0.948 0.615,0.198 10 false 19 5.281,4.083 6.854,4.542 1.573,0.458 10 false Skid Control ECU (Brake Actuator Assembly) 5.281,3.917 5.896,4.115 0.615,0.198 10 false A42 2.938,4.344 4.802,4.615 1.865,0.271 10 false : CAN Communication Line 4.74,2.594 5.354,2.792 0.615,0.198 10 false 13*1 1.583,2.917 2.5,3.083 0.917,0.167 10 false *1: for LHD 1.583,3.25 2.438,3.49 0.854,0.24 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (TRC/VSC OFF MODE)

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode Normal, TRC OFF, VSC Expert Mode or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
-
Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display
TRC/VSC Off Mode
50003 105 282

b.

Check the indicator light and mode condition on the GTS changes according to VSC OFF switch operation.

Standard:
Switch Operation Mode Condition Display TRC OFF Indicator Light*1 Multi-information Display (TRC OFF message)*2 VSC OFF Indicator Light
Not pressed Normal Does not come on Not displayed Does not come on
Pressing the VSC OFF switch (electric parking brake switch assembly) TRC OFF Comes on Displayed Does not come on
Pressing and holding the VSC OFF switch (electric parking brake switch assembly) VSC OFF Comes on Displayed Comes on


*1: for Color TFT Type

*2: for Monochrome TFT Type



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display are normal. C



A

4.PERFORM ACTIVE TEST USING GTS (TRC (TRAC) OFF INDICATOR LIGHT AND VSC OFF INDICATOR LIGHT)

B

C

4.PERFORM ACTIVE TEST USING GTS (TRC (TRAC) OFF INDICATOR LIGHT AND VSC OFF INDICATOR LIGHT)
a.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
TRC(TRAC) OFF Indicator Light TRC OFF indicator light*1 Multi-information display (TRC OFF massage)*2 Display ON/OFF Observe combination meter assembly
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Observe combination meter assembly
Chassis > ABS/VSC/TRC/EPB > Active Test
Tester Display
TRC(TRAC) OFF Indicator Light
50004 105 78
Chassis > ABS/VSC/TRC/EPB > Active Test
Tester Display
VSC OFF Indicator Light
50004 105 79

b.

Check the multi-information display (TRC OFF message)*1, TRC OFF indicator light*2 and VSC OFF indicator light on the combination meter assembly turn on or off in accordance with GTS operation.

OK:

The multi-information display (TRC OFF message)*1, TRC OFF indicator light*2 and VSC OFF indicator light turn on or off in accordance with GTS operation.


*1: for Color TFT Type

*2: for Monochrome TFT Type



Result:
Proceed to
OK
NG



OK

5.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

NG

7.INSPECT COMBINATION METER ASSEMBLY
5.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY
a.

Remove the electric parking brake switch assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>REMOVAL


b.

Inspect the electric parking brake switch assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A42-6 (CSW) - F67-13 (+) Always Below 1 Ω
A42-6 (CSW) or F67-13 (+) - Body ground Always 10 kΩ or higher
F67-8 (E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A42-6 (CSW) - F67-11 (+) Always Below 1 Ω
A42-6 (CSW) or F67-11 (+) - Body ground Always 10 kΩ or higher
F67-8 (E) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly using the GTS. (for Color TFT Type)

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. VSC OFF
50004 122 94

b.

Perform the Active Test of the combination meter assembly using the GTS. (for Monochrome TFT Type)

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
VSC TRC Indicator
50004 122 102
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. VSC OFF
50004 122 80

c.

Check the combination meter assembly.

OK:

The multi-information display (TRC OFF message) (for Color TFT Type), TRC OFF indicator light (for Monochrome TFT Type) and VSC OFF indicator light turn on or off in accordance with GTS operation.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C