Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM (for 8NR-FTS)
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297888 CRUISE CONTROL SYSTEM(for 8NR-FTS) C

CRUISE CONTROL  CRUISE CONTROL SYSTEM(for 8NR-FTS)  P157800  Brake System  


DESCRIPTION

This DTC is stored when the vehicle stability control system has a problem. Check the vehicle stability control system when DTC P157800 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
P157800 Brake System When the ignition switch ON and the cruise control system is operating, a malfunction in the vehicle stability control system is detected for 0.2 seconds or more.
·

Vehicle stability control system

·

ECM

·

Skid control ECU (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:

Before replacing the ECM refer to Service Bulletin.


PROCEDURE

1.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105
OK:

Vehicle stability control system DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTCs (CRUISE CONTROL SYSTEM)

NG

2.CHECK FOR DTCs (CRUISE CONTROL SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for 8NR-FTS)>DTC CHECK / CLEAR

Powertrain > Cruise Control > Clear DTCs
50002 374

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.

1.

Drive the vehicle at a speed for which cruise control operation is possible.

2.

Turn the cruise control system on using the cruise control main switch (ON/OFF button).

3.

Push the cruise control main switch to -SET to begin control of vehicle speed using the cruise control system.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for 8NR-FTS)>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 374
OK:

DTC P157800 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.REPLACE ECM
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (CRUISE CONTROL SYSTEM)
4.CHECK FOR DTCs (CRUISE CONTROL SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for 8NR-FTS)>DTC CHECK / CLEAR

Powertrain > Cruise Control > Clear DTCs
50002 374

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.

1.

Drive the vehicle at a speed for which cruise control operation is possible.

2.

Turn the cruise control system on using the cruise control main switch (ON/OFF button).

3.

Push the cruise control main switch to -SET to begin control of vehicle speed using the cruise control system.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for 8NR-FTS)>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 374
OK:

DTC P157800 is not output.



Result:
Result Proceed to
OK A
NG (for RHD) B
NG (for LHD) C



A

END

B

C