Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2016.10–2020.08
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297889 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Distance Control Switch Circuit  


DESCRIPTION

The distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The distance control switch is installed in the steering pad switch assembly. The vehicle-to-vehicle distance set value can be changed by operating the steering pad switch assembly (distance control switch) while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.

WIRING DIAGRAM

C367152E04
1.344,0.75 2.875,0.99 1.531,0.24 10 false Distance Control Switch 0.917,2.646 2.885,2.938 1.969,0.292 10 false Steering Pad Switch Assembly 3.115,0.375 3.271,0.573 0.156,0.198 10 false 4 3.073,0.583 3.271,0.781 0.198,0.198 10 false z1 3.083,2.031 3.281,2.229 0.198,0.198 10 false z1 3.104,1.833 3.26,2.031 0.156,0.198 10 false 7 3.833,0.479 4.26,0.688 0.427,0.208 10 false DIST 3.833,1.927 4.26,2.135 0.427,0.208 10 false ECC 3.24,2.615 4.323,3.01 1.083,0.396 10 false Spiral Cable Sub-assembly 4.271,2.042 4.635,2.25 0.365,0.208 10 false F29 4.354,1.833 4.51,2.031 0.156,0.198 10 false 2 4.281,0.583 4.646,0.792 0.365,0.208 10 false F29 4.313,0.385 4.635,0.604 0.323,0.219 10 false 12 5.5,0.5 5.688,0.719 0.188,0.219 10 false 3 5.667,0.563 6.156,0.771 0.49,0.208 10 false LKSW 5.427,1.125 5.792,1.333 0.365,0.208 10 false R5 5.427,1.281 6.76,1.719 1.333,0.438 10 false Forward Recognition Camera 5.292,2.031 5.656,2.24 0.365,0.208 10 false A38 5.313,1.833 5.521,2.031 0.208,0.198 10 false 41 5.292,2.531 5.656,2.74 0.365,0.208 10 false C62 5.323,2.323 5.531,2.521 0.208,0.198 10 false 53 5.677,2.01 6.104,2.219 0.427,0.208 10 false ECCS 5.688,2.521 5.948,2.74 0.26,0.219 10 false E1 5.823,2.99 6.26,3.219 0.438,0.229 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the ECM, refer to Service Bulletin.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.READ VALUE USING GTS (DISTANCE CONTROL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise 2 / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Distance Control Switch Distance control switch signal ON or OFF ON: Distance control switch on
OFF: Distance control switch off
-
Powertrain > Radar Cruise2 > Data List
Tester Display
Distance Control Switch
50003 197 5
OK:

The Data List item shown in the table changes according to the operation of the steering pad switch assembly (distance control switch).



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA, ECM AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA, ECM AND BODY GROUND)
a.

Disconnect the spiral cable sub-assembly connector.


b.

Disconnect the forward recognition camera connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-12 (DIST) - R5-3 (LKSW) Always Below 1 Ω
F29-2 (ECC) - A38-41 (ECCS) Always Below 1 Ω
F29-12 (DIST) or R5-3 (LKSW) - Body ground Always 10 kΩ or higher
F29-2 (ECC) or A38-41 (ECCS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the C62 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-2 (ECC) or C62-53 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK ECM (ECM TERMINALS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ECM (ECM TERMINALS)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-41 (ECCS) - C62-53 (E1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG