The skid control ECU (brake actuator assembly) sends signals such as cruise control cancel signals and brake demand response signals to the ECM when the dynamic radar cruise control system is operating.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P163081 | Communication Error from VSC to ECM Invalid Serial Data Received | w/o Full-speed range following function:
·
While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, communication data from the skid control ECU (brake actuator assembly) is logically inconsistent for approximately 0.5 seconds or more. w/ Full-speed range following function:
·
While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, communication data from the skid control ECU (brake actuator assembly) is logically inconsistent for approximately 0.5 seconds or more. |
·
CAN communication circuit ·
Skid control ECU (brake actuator assembly) ·
ECM |
Before replacing the ECM refer to Service Bulletin.
First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Using the GTS, check if the CAN communication system is functioning normally.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | OK |
| CAN communication system DTCs are output | NG |
OK
NG
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Turn the ignition switch to ON.
Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).
w/ Full-speed range following function: Drive the vehicle at 5 km/h (3 mph) or more for 0.5 seconds or more.
w/o Full-speed range following function: Drive the vehicle at 36 km/h (22 mph) or more for 0.5 seconds or more.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC P163081 is not output | A |
| DTC P163081 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Replace the brake actuator assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Turn the ignition switch to ON.
Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).
w/ Full-speed range following function: Drive the vehicle at 5 km/h (3 mph) or more for 0.5 seconds or more.
w/o Full-speed range following function: Drive the vehicle at 36 km/h (22 mph) or more for 0.5 seconds or more.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC P163081 is not output | A |
| DTC P163081 is output | B |
A
B