Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM32H0E _58 Vehicle Interior _060018 LIGHTING (INT) _0298022 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Engine Switch Illumination Circuit  


DESCRIPTION

The illuminated entry system controls the engine switch illumination.

WIRING DIAGRAM

E309266E48
3.323,0.719 3.938,0.917 0.615,0.198 10 false SWIL 3.271,1.344 3.885,1.542 0.615,0.198 10 false AGND 3.74,0.719 3.896,0.917 0.156,0.198 10 false 9 3.74,1.344 3.896,1.542 0.156,0.198 10 false 6 4.792,0.719 5.104,0.917 0.313,0.198 10 false 10 4.792,1.354 5.104,1.552 0.313,0.198 10 false 11 4.552,2 5.01,2.198 0.458,0.198 10 false F1 5.063,0.719 5.677,0.917 0.615,0.198 10 false SWIL 5.063,1.354 5.677,1.552 0.615,0.198 10 false AGND 1.375,2.01 1.833,2.208 0.458,0.198 10 false F59 1.365,2.167 3.198,2.365 1.833,0.198 10 false Engine Switch 4.542,2.146 6.396,2.594 1.854,0.448 10 false Certification ECU (Smart Key ECU Assembly) 5.906,0.667 6.219,0.865 0.313,0.198 10 false +B

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power/Engine SW Light Engine switch illumination OFF or ON When performing this Active Test, make sure the following condition is met:
The engine switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the engine switch is on (ACC) or on (IG), or the engine is running.
Body Electrical > Entry&Start > Active Test
Tester Display
Power/Engine SW Light
50004 125 27
OK:

Engine switch illumination comes on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ENGINE SWITCH
2.INSPECT ENGINE SWITCH

b.

Inspect the engine switch.


OK:

Engine switch illumination is normal.



Result:
Result Proceed to
OK A
NG (for 8NR-FTS with LHD) B
NG (for 8NR-FTS with RHD) C
NG (for 3ZR-FAE) D



A

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

B

C

D

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F59-9 (SWIL) - F1-10 (SWIL) Always Below 1 Ω
F59-6 (AGND) - F1-11 (AGND) Always Below 1 Ω
F59-9 (SWIL) or F1-10 (SWIL) - Body ground Always 10 kΩ or higher
F59-6 (AGND) or F1-11 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR