The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the front door window frame moulding removal/installation are shown below.
*1: When performing learning using the GTS.
*2: w/ Stop and start system
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
75720
2.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY
75072A
3.REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY
When removing the front door outside moulding sub-assembly, heat the vehicle body and front door outside moulding sub-assembly using a heat light.
| Item | Temperature |
|---|---|
| Front Door Outside Moulding Sub-assembly | 40 to 60°C (104 to 140°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the vehicle body or moulding excessively.
Using a heat light, heat the front door outside moulding sub-assembly.
| *a | Double-sided Tape |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
Protective Tape |
Apply protective tape around the front door outside moulding sub-assembly as shown in the illustration.
Using a moulding remover D, disengage the clip and guide, and separate the double-sided tape and caulking sponge to remove the front door outside moulding sub-assembly as shown in the illustration.
67862
4.DISCONNECT FRONT DOOR WEATHERSTRIP
Using a clip remover, disengage the clips to disconnect the front door weatherstrip.
67664
5.REMOVE DOOR FRAME UPPER GARNISH
68151C
6.REMOVE FRONT DOOR GLASS RUN
67402F
7.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
68126
8.REMOVE FRONT DOOR FIX WINDOW GLASS
75754A
9.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING
Insert a 4.0 mm (0.157 in.) drill bit into a drill.
| *a | Tape |
Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.
| Area | Measurement |
|---|---|
| A | 5.0 mm (0.197 in.) |
Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.
Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 6 rivets.
Be careful of the drilled rivets, as they may be hot.
Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
Prying the rivets with the drill may damage the rivet installation holes or drill bit.
Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.
Disengage the guide to remove the front door upper window frame moulding from the door frame.
67914
10.REMOVE FRONT DOOR SCUFF PLATE
62112
11.REMOVE COWL SIDE TRIM BOARD
75752C
12.REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING
Disconnect each connector.
Disengage each clamp.
Remove the 5 bolts and front door panel sub-assembly.
To prevent damage, when removing the front door panel sub-assembly, make sure that there are enough people available to hold it securely.
Insert a 4.0 mm (0.157 in.) drill bit into a drill.
| *a | Tape |
Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.
| Area | Measurement |
|---|---|
| A | 5.0 mm (0.197 in.) |
Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.
Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 2 rivets and front door front window frame moulding.
Be careful of the drilled rivets, as they may be hot.
Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
Prying the rivets with the drill may damage the rivet installation holes or drill bit.
Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.