Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2016.10–2019.09
RM32H0E _59 Vehicle Exterior _060017 DOOR / HATCH _0295665 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the front door removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Pre-collision System
Initialize back door lock Power door lock control system (Click here)
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)*2 Stop and start system (Click here)
·

Front door window regulator assembly

·

Front door glass sub-assembly

·

Front door glass run


Initialize Power Window Control System
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

*2: w/ Stop and start system

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
·
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69284C 3.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B458070C01
0,0 0,0 false
V113147

Remove in this Direction


Using a moulding remover A, disengage the claws to remove the front door inside handle bezel plug as shown in the illustration.


Hide 74232 4.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)

a.
B458071C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws, clips and guides as shown in the illustration.


b.
B458072

Disconnect the 2 connectors to remove the multiplex network master switch assembly with front armrest base upper panel.


Hide 74231 5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)

a.
B458073C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws, clips and guides as shown in the illustration.


b.
B458074

Disconnect the connector to remove the power window regulator switch assembly with front armrest base upper panel.


Hide 67602 6.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B458075

Remove the 3 screws.


b.
B458076C02
2.333,1.188 1.781,0.625 true 3.083,1.375 2.646,1.208 true 1.594,0.5 1.906,0.698 0.313,0.198 10 false *a 3.156,1.344 3.344,1.552 0.188,0.208 10 false *a
*a Clip (A)
V113146

Place Hands Here
V113147

Remove in this Direction


Disengage the clips (A), other clips and guide as shown in the illustration.


c.
B483922C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the front door trim board sub-assembly with the front door glass inner weatherstrip and front door belt seal as shown in the illustration.


d.

w/ Illumination:

i.

Disconnect the connector.



e.
B458077C01
2.292,0.958 2.531,0.708 true 2.542,1.427 2.292,1.167 true 2.531,0.521 2.74,0.708 0.208,0.188 10 true *1 2.521,1.396 2.729,1.583 0.208,0.188 10 true *2
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly
V113147

Remove in this Direction


Disengage the guides to disconnect the front door inside locking cable assembly and front door lock remote control cable assembly to remove the front door trim board sub-assembly as shown in the illustration.


Hide 69206B 7.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

B458078

a.

Disengage the claw and guides to remove the front door inside handle sub-assembly.


Hide 81080S 8.REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (w/ Illumination)

Hide 67492A 9.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B458079

Disengage the clips to remove the front door lower frame bracket garnish.


Hide 68172A 10.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP

a.
B483923C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws remove the front door glass inner weatherstrip with the front door belt seal as shown in the illustration.


Hide 68195 11.REMOVE FRONT DOOR BELT SEAL

a.
B458081C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door belt seal from the front door glass inner weatherstrip as shown in the illustration.


Hide 67838A 12.REMOVE FRONT DOOR VENT SEAL

a.
B458082

Remove the front door vent seal.


Hide 87940 13.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

Hide 87912A 14.REMOVE OUTER MIRROR PROTECTOR

a.
B458083C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the 2 screws.


b.

Disengage the claws to remove the outer mirror protector as shown in the illustration.


Hide 67832 15.REMOVE FRONT DOOR SERVICE HOLE COVER

a.
B458084

Turn the 3 door weatherstrip clips 45° and remove it clips as shown in the illustration.


b.

Disengage the clips to remove the front door service hole cover.


Hide 89835 16.REMOVE DOOR SIDE AIRBAG SENSOR (w/ Airbag Sensor)

Hide 68102 17.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

a.
B458085

Remove the hole plug.


b.

for Driver Side:

i.

Connect the multiplex network master switch assembly.


ii.

Connect the cable to the negative (-) battery terminal.


iii.

Move the front door glass sub-assembly so that the door glass bolts can be seen.


iv.

Disconnect the cable from the negative (-) battery terminal.


v.

Disconnect the multiplex network master switch assembly.



c.

for Front Passenger Side:

i.

Connect the power window regulator switch assembly.


ii.

Connect the cable to the negative (-) battery terminal.


iii.

Move the front door glass sub-assembly so that the door glass bolts can be seen.


iv.

Disconnect the cable from the negative (-) battery terminal.


v.

Disconnect the power window regulator switch assembly.



d.
B470601

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the front door glass sub-assembly to fall.



e.
B470602C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the front door glass sub-assembly as shown in the illustration.

NOTICE:

Do not damage the front door glass sub-assembly.



Hide 67831C 18.REMOVE NO. 2 FRONT DOOR SERVICE HOLE COVER

a.
B458088

Disengage the claws to remove the No. 2 front door service hole cover.


Hide 19.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.
B458089C01
1.5,0.5 2.063,0.615 true 1.292,0.406 1.458,0.573 0.167,0.167 10 true *a
*a Temporary Bolt


Disconnect the connector.


b.

Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.



c.

Remove the 5 bolts and front door window regulator sub-assembly.


d.

Remove the temporary bolt from the front door window regulator assembly.


Hide 67664 20.REMOVE DOOR FRAME UPPER GARNISH

a.
B458090

Disengage the guides to remove the door frame upper garnish.


Hide 68151C 21.REMOVE FRONT DOOR GLASS RUN

a.
B470603

Remove the front door glass run.


Hide 67402F 22.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.

Raise up the front door weatherstrip.


b.
B458105

Remove the screw.


c.

Remove the 2 bolts and front door front lower frame sub-assembly.


d.

Install the front door weatherstrip.


Hide 67404F 23.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B458123C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the bolt.


b.

Disengage the guide to remove the front door rear lower frame sub-assembly as shown in the illustration.


Hide 69217D 24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B458093C01
2.813,1.865 3.146,1.781 false 3.219,1.667 3.396,1.833 0.177,0.167 10 false *1
*1 Hole Plug
V113147

Remove in this Direction


Remove the hole plug.


b.

Using a T30 "TORX" socket wrench, loosen the screw.


c.

Remove the front door outside handle cover with front door lock cylinder assembly as shown in the illustration.


d.
B393872C05
1.844,1.188 2.26,1.438 true 2.302,1.458 2.615,1.656 0.313,0.198 10 false *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claw and guides to remove the front door outside handle cover as shown in the illustration.


Hide 69217D 25.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B458094C01
0.313,1.719 0.583,1.719 false 0.125,1.635 0.438,1.792 0.313,0.156 10 false *1
*1 Hole Plug
V113147

Remove in this Direction


Remove the hole plug.


b.

Using a T30 "TORX" socket wrench, loosen the screw.


c.

Disengage the claws to remove the front door outside handle cover as shown in the illustration.


Hide 69220 26.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B458092C01
0.969,0.802 1.385,0.385 true 1.458,0.281 1.625,0.448 0.167,0.167 10 true *a
*a Protective Tape


w/ Entry and Start System:

i.

Disengage the claws.


ii.

Using a screwdriver with its tip wrapped in protective tape, disconnect the connector.



b.
B458095C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door outside handle assembly as shown in the illustration.


Hide 69241H 27.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B458096C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws and guide to remove the front door front outside handle pad as shown in the illustration.


Hide 69242E 28.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B458097C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guides to remove the front door rear outside handle pad as shown in the illustration.


Hide 69040A 29.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

Hide 69202A 30.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

w/ Entry and Start System:

i.
B458098C01
2.344,0.938 2.083,0.521 true 0.667,0.552 0.333,0.417 0.333,0.417 0.667,0.302 true 1.875,0.427 2.042,0.594 0.167,0.167 10 true *a 0.125,0.313 0.292,0.479 0.167,0.167 10 true *b
*a Grommet
*b Guide
V113147

Remove in this Direction


Using a T30 "TORX" socket wrench, loosen the screw.


ii.

Disengage the grommet and guides to separate the front door outside handle frame sub-assembly as shown in the illustration.


iii.
B458099C01
0.438,1.208 0.635,0.969 false 1.729,1.281 1.698,0.99 false 2.385,1.292 2.385,0.969 false 1.698,1.354 1.969,1.552 0.271,0.198 10 false *a 0.354,1.271 0.625,1.469 0.271,0.198 10 false *b 2.333,1.333 2.604,1.531 0.271,0.198 10 false *b
*a Guide
*b Clamp


Disengage the clamps and guide to remove the front door outside handle frame sub-assembly.



b.

w/o Entry and Start System:

i.
B458100C01
2.615,1.552 2.49,1.135 true 0.667,0.552 0.396,0.396 0.396,0.396 0.667,0.323 true 2.583,1.563 2.833,1.781 0.25,0.219 10 true *a 0.198,0.302 0.365,0.5 0.167,0.198 10 true *b
*a Grommet
*b Guide
V113147

Remove in this Direction


Using a T30 "TORX" socket wrench, loosen the screw.


ii.

Disengage the grommet and guides to remove the front door outside handle frame sub-assembly as shown in the illustration.



c.
B458101

w/ Protector:

i.

Remove the 3 screws and door outside handle protector.



Hide 69312 31.REMOVE FRONT DOOR LOCK OPEN ROD

a.
B458102C01
2.385,1.448 2.75,1.25 false 2.823,1.146 3.135,1.302 0.313,0.156 10 false *a
*a Snap
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the snap to remove the front door lock open rod from the front door outside frame sub-assembly as shown in the illustration.


Hide 68610 32.REMOVE FRONT DOOR CHECK ASSEMBLY

a.
B458103

Remove the 3 bolts and front door check assembly.


Hide 67862 33.REMOVE FRONT DOOR WEATHERSTRIP

a.
B458104C01
0.604,1.281 0.844,1.083 false 0.427,1.292 0.74,1.49 0.313,0.198 10 false *a
*a Clip (A)


Using a clip remover, disengage the clip (A) and other clips to remove the front door weatherstrip.


Hide 67837B 34.REMOVE FRONT DOOR DUST PROOF SEAL

a.
B458109

Remove the 3 front door dust proof seals.


Hide 86160 35.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY (w/ Speaker)

Hide 86262E 36.REMOVE FRONT SPEAKER COVER (w/o Speaker)

a.
B458210

Disconnect the connector.


b.
B458211

Using a drill bit with a diameter of less than 5 mm (0.197 in.), drill out the 3 rivet heads.

NOTICE:
·

Do not drill the rivet at an angle as this will cause damage to the drill and rivet installation hole. Line up the drill with the rivet, and carefully drill out the rivet head.

·

Be careful as the drilled rivet will be very hot.




c.

Continue drilling and push out the remaining rivet fragments.


d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.


e.

Disengage the claw and guide to remove the front speaker cover.


Hide 68126 37.REMOVE FRONT DOOR FIX WINDOW GLASS

a.
B458106C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door fix window glass with front door fix window weatherstrip as shown in the illustration.


Hide 68216 38.REMOVE FRONT DOOR FIX WINDOW WEATHERSTRIP

a.
B458107

Remove the front door fix window weatherstrip from the front door fix window glass.


Hide 67001A 39.REMOVE FRONT DOOR PANEL CUSHION

a.
B458108

Using a clip remover, disengage the claws to remove the 2 front door panel cushions.


Hide 75732A 40.REMOVE FRONT DOOR OUTSIDE MOULDING

Hide 75788A 41.REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY

Hide 42.REMOVE HOLE CAP

a.
B458110

Remove the hole cap.


Hide 75720 43.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

Hide 67914 44.REMOVE FRONT DOOR SCUFF PLATE

Hide 62112 45.REMOVE COWL SIDE TRIM BOARD

Hide 75752C 46.REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING

Hide 75754A 47.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

Hide 75966B 48.REMOVE NO. 4 FRONT DOOR STRIPE

Hide 75986G 49.REMOVE FRONT DOOR OUTSIDE STRIPE

Hide 75976G 50.REMOVE NO. 2 FRONT DOOR STRIPE