Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE (for Rear Door) › 2016.10–2019.09
RM32H0E _59 Vehicle Exterior _060783 EXTERIOR PANELS / TRIM _0298079 BLACK OUT TAPE(for Rear Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Rear Door)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the black out tape removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Pre-collision System
Initialize back door lock Power door lock control system (Click here)
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)*2 Stop and start system (Click here)
·

Rear door window regulator assembly

·

Rear door glass sub-assembly

·

Rear door glass run


Initialize Power Window Control System
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

*2: w/ Stop and start system

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69284D 3.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

Hide 74272A 4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

Hide 67498 5.REMOVE REAR DOOR REAR FRAME BRACKET

Hide 67604 6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 68199 7.REMOVE REAR DOOR BELT REAR SEAL

Hide 68174A 8.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP

Hide 68197 9.REMOVE REAR DOOR BELT SEAL

Hide 67842E 10.REMOVE REAR DOOR SERVICE HOLE COVER

Hide 67872 11.REMOVE REAR DOOR WEATHERSTRIP

Hide 67408F 12.REMOVE REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY

Hide 68104 13.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Hide 67674A 14.REMOVE REAR DOOR FRAME GARNISH

Hide 68152C 15.REMOVE REAR DOOR GLASS RUN

Hide 68124B 16.REMOVE REAR DOOR QUARTER WINDOW GLASS

Hide 75978H 17.REMOVE REAR DOOR LOWER OUTSIDE STRIPE

HINT:

When removing the rear door lower outside stripe, heat the vehicle body and rear door lower outside stripe using a heat light.


Heating Temperature
Item Temperature
Rear Door Lower Outside Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


a.

Using a heat light, heat the rear door lower outside stripe and vehicle body.


b.
B458793

Pull back on one of the ends of the rear door lower outside stripe to remove it.

HINT:

When pulling on the rear door lower outside stripe, pull it parallel to the vehicle body.



Hide 75988E 18.REMOVE REAR DOOR OUTSIDE STRIPE

HINT:

When removing the rear door outside stripe, heat the vehicle body and rear door outside stripe using a heat light.


Heating Temperature
Item Temperature
Rear Door Outside Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


a.

Using a heat light, heat the rear door outside stripe and vehicle body.


b.
B458792

Pull back on one of the ends of the rear door outside stripe to remove it.

HINT:

When pulling on the rear door outside stripe, pull it parallel to the vehicle body.