Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › 2016.10–2019.09
RM32H0E _56 Audio / Visual / Telematics _060052 TELEMATICS _0298115 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B1570  Red LED Error  


DESCRIPTION

This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch indicator (red) circuit of the mayday switch assembly (manual (SOS) switch).

The manual (SOS) switch indicator (red) illuminates for 10 seconds and turns off when the ignition switch is turned to ON.

If a malfunction in the telematics system is detected, the manual (SOS) switch indicator (red) will illuminate. However, the manual (SOS) switch indicator (red) may not illuminate when this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1570 Red LED Error Current for the manual (SOS) switch indicator (red) exceeds malfunction threshold for 10 seconds when the ignition switch is ON.
·

Telematics transceiver

·

Map light assembly

·

Mayday switch assembly (manual (SOS) switch)

·

Wire harness or connector



WIRING DIAGRAM

E359943E01
5.438,1.958 5.896,2.156 0.458,0.198 10 false F51 5.417,2.135 6.906,2.417 1.49,0.281 10 false Telematics Transceiver 5.792,1.021 6.406,1.219 0.615,0.198 10 false IND1 5.781,1.344 6.396,1.542 0.615,0.198 10 false SIG- 5.5,0.875 5.813,1.073 0.313,0.198 10 false 11 5.531,1.333 5.844,1.531 0.313,0.198 10 false 26 3.385,0.896 4,1.094 0.615,0.198 10 false IND1 2.531,0.917 3.146,1.115 0.615,0.198 10 false IND1 3.302,1.344 3.917,1.542 0.615,0.198 10 false GND3 2.5,1.354 3.115,1.552 0.615,0.198 10 false GND 3.792,0.906 3.948,1.104 0.156,0.198 10 false 6 3.792,1.323 3.948,1.521 0.156,0.198 10 false 1 0.51,2.958 0.823,3.156 0.313,0.198 10 false R4 0.51,3.115 3.26,3.313 2.75,0.198 10 false Map Light Assembly 0.76,1.99 2.396,2.344 1.635,0.354 10 false Mayday Switch Assembly (Manual (SOS) Switch) 1.417,1.25 1.875,1.448 0.458,0.198 10 false RED

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


HINT:

If DTC B1570 is stored, the manual (SOS) switch indicator (red) may not illuminate when another DTC is stored.


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH INPUT VOLTAGE)
2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH INPUT VOLTAGE)
a.
E359858C01
0.094,0.896 0.51,1.188 0.417,0.292 0.938,1.948 1.375,1.344 true 2.74,1.958 2.365,1.354 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 0.219,0.938 0.531,1.135 0.313,0.198 10 false R4 0.563,1.865 1.177,2.063 0.615,0.198 10 false IND1 2.802,1.906 3.417,2.104 0.615,0.198 10 false GND3
*a Component with harness connected
(Map Light Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R4-6 (IND1) - R4-1 (GND3) 2 seconds after ignition switch turned to ON → Ignition switch off 2 to 5 V
→ Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT MAYDAY SWITCH ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)

NG

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
3.INSPECT MAYDAY SWITCH ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)
a.

Remove the mayday switch assembly (manual (SOS) switch).

Click hereAudio / Visual / Telematics>TELEMATICS>MAYDAY SWITCH>REMOVAL


b.

Inspect the mayday switch assembly (manual (SOS) switch).

Click hereAudio / Visual / Telematics>TELEMATICS>MAYDAY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE MAP LIGHT ASSEMBLY

NG

REPLACE MAYDAY SWITCH ASSEMBLY (MANUAL (SOS) SWITCH)

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
a.

Disconnect the F51 telematics transceiver connector.


b.

Disconnect the R4 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F51-11 (IND1) - R4-6 (IND1) Always Below 1 Ω
F51-11 (IND1) or R4-6 (IND1) - Body ground Always 10 kΩ or higher
F51-26 (SIG-) - R4-1 (GND3) Always Below 1 Ω
F51-26 (SIG-) or R4-1 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT