These DTCs are stored when a malfunction occurs in the roof antenna assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1573 | Disconnect/Short in Telephone Antenna Circuit | Roof antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds when the ignition switch is ON.
(Short circuit) |
·
Telematics transceiver ·
Roof antenna assembly ·
Antenna cord sub-assembly ·
No. 3 antenna cord sub-assembly |
| B15CB | Telephone Antenna Disconnected | Roof antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds when the ignition switch is ON.
(Open circuit) |
·
Telematics transceiver ·
Roof antenna assembly ·
Antenna cord sub-assembly ·
No. 3 antenna cord sub-assembly |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 10 seconds.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the roof antenna assembly.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
| *a | Component without harness connected
(Roof Antenna Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 - 4a | Always | 4 to 11 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 3 antenna cord sub-assembly.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA CORD>REMOVAL
| *a | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Roof Antenna Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 - RA-4 | Always | Below 1 Ω |
| B-1a - RA-4a | Always | Below 1 Ω |
| B-1 or RA-4 - Body ground | Always | 10 kΩ or higher |
| B-1a or RA-4a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the antenna cord sub-assembly.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA CORD>REMOVAL
| *a | Front view of wire harness connector
(to Telematics Transceiver) |
| *b | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| TA-1 (TEL) - A-1 | Always | Below 1 Ω |
| TA-1a - A-1a | Always | Below 1 Ω |
| TA-1 (TEL) or A-1 - Body ground | Always | 10 kΩ or higher |
| TA-1a or A-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT