Home › Engine / Hybrid System › 8NR-FTS (FUEL) › FUEL SYSTEM › 2016.10–2020.08
RM32H0E _51 Engine / Hybrid System _059909 8NR-FTS FUEL _0293894 FUEL SYSTEM L

8NR-FTS FUEL  FUEL SYSTEM  PRECAUTION  


CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.


·
A344817

Because the weight of the fuel tank sub-assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the components could fall down.



IGNITION SWITCH EXPRESSIONS


a.

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)



PRECAUTION


NOTICE:
·

Keep fuel away from rubber or leather parts.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




DISCHARGE FUEL SYSTEM PRESSURE


NOTICE:
·

Make sure the engine coolant temperature is 60°C (140°F) or less when performing this procedure.

·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

Pressure will still remain in the fuel lines even after performing the following procedure. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.



a.

When discharging fuel system pressure by disconnecting the EFI MAIN NO. 2 relay:

i.

Remove the No. 1 relay block cover.


ii.

Remove the EFI MAIN NO. 2 relay.


iii.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



iv.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P008700 (Fuel Rail / System Pressure - Too Low), P017100 (System Too Lean), P160300 (Engine Stall History), P160400 (Startability Malfunction) or P160500 (Rough Idling) may be stored. Clear the DTCs before proceeding to the next step.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR



v.

Remove the fuel tank cap and discharge the pressure from the fuel tank assembly.


vi.

Disconnect the cable from the negative (-) battery terminal.

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



vii.

Install the EFI MAIN NO. 2 relay.


viii.

Install the No. 1 relay block cover.



b.

When discharging fuel system pressure by disconnecting the fuel pump connector:

i.

Disconnect the rear center seat outer belt assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


ii.

Remove the bench type rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


iii.

Remove the rear seat cushion lock hook.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


iv.
A393040C01
0.083,0.083 0.333,0.292 0.25,0.208 12 true *A 0.083,2.5 0.333,2.719 0.25,0.219 12 true *B
*A for 2WD
*B for AWD


Remove the rear floor service hole cover.



v.

Disconnect the fuel suction tube with pump and gauge assembly connector.


vi.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



vii.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P008700 (Fuel Rail / System Pressure - Too Low), P017100 (System Too Lean), P160300 (Engine Stall History), P160400 (Startability Malfunction) or P160500 (Rough Idling) may be stored. Clear the DTCs before proceeding to the next step.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR



viii.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.


ix.

Disconnect the cable from the negative (-) battery terminal.

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



x.

Connect the fuel suction tube with pump and gauge assembly connector.


xi.

xii.

Install the rear seat cushion lock hook.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>INSTALLATION


xiii.

Install the bench type rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>INSTALLATION


xiv.

Connect the rear center seat outer belt assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>INSTALLATION




FUEL LINE


a.

When disconnecting a high-pressure fuel line, a large amount of fuel will spray. Perform the following procedure:

i.

Discharge fuel system pressure.


ii.

Disconnect the fuel tube.


iii.

Drain the fuel remaining inside the fuel pump tube into a container.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



b.

Quick Type A:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A310731

Open the cover of the No. 1 fuel pipe clamp and remove the No. 1 fuel pipe clamp from the fuel tube connector. (Cover Type A)


ii.

Check that there is no foreign matter around the fuel tube connector before disconnecting it. Clean it if necessary.


iii.
A313095

Release the lock of the fuel tube connector cover. (Cover Type B)


iv.

Check whether there is any foreign matter on the fuel pipe around the fuel tube connector before disconnecting it and remove the foreign matter as necessary.


v.
A159424C31
2.271,1.51 2.729,1.198 2.729,1.198 2.531,1.51 false 2.177,3.719 2.177,4.042 2.177,4.042 1.729,4.042 false 2,3.719 2,4.042 false 2.552,3.354 2.271,3.073 2.271,3.073 2.167,3.073 false 2.667,3.896 2.833,4.052 2.833,4.052 2.927,4.052 false 1.177,3.385 0.938,3.104 0.938,3.104 0.833,3.104 false 2.823,3.458 2.927,3.208 2.927,3.208 3.021,3.208 false 2.781,1.083 2.969,1.271 0.188,0.188 10 false *a 2,3 2.198,3.219 0.198,0.219 10 false *a 1.552,3.958 1.729,4.188 0.177,0.229 10 false *b 2.99,3.979 3.188,4.198 0.198,0.219 10 false *c 3.073,3.135 3.271,3.354 0.198,0.219 10 false *e 0.667,3.031 0.865,3.25 0.198,0.219 10 false *d
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Nylon Tube
*e Fuel Pipe
V100135

Pinch
V100136

Pull off


Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



vi.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




vii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


viii.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



c.

Quick Type A:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A303841C01
1.542,1.563 1.698,1.76 0.156,0.198 10 false .
V100135

Pull


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iii.

Install the No. 1 fuel pipe clamp to the fuel tube connector and close the cover of the No. 1 fuel pipe clamp. (Clamp Type A)


iv.

Engage the lock of the fuel tube connector cover. (Cover Type B)




d.

Quick Type B:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A318103C02
0.698,2.625 0.854,2.625 0.854,2.625 1.042,3.135 false 0.24,3.021 0.375,3.021 0.375,3.021 0.51,3.333 false 0.99,4.021 0.99,3.75 false 2.146,1.844 2.417,1.844 false 1.865,3.906 1.865,3.583 false 2.49,3.25 2.542,2.938 2.542,2.938 2.656,2.938 false 1.688,3.594 1.688,3.906 1.688,3.906 2.208,3.906 false 2.146,1.573 2.417,1.573 false 2.865,1.563 3.135,1.563 false 1.969,1.76 2.281,1.917 0.313,0.156 10 false *a 0.063,2.948 0.375,3.104 0.313,0.156 10 false *b 2.708,2.865 3.021,3.021 0.313,0.156 10 false *c 0.906,4.052 1.219,4.208 0.313,0.156 10 false *d 2.25,3.833 2.563,3.99 0.313,0.156 10 false *e 0.521,2.542 0.833,2.698 0.313,0.156 10 false *a 3.198,1.5 3.375,1.677 0.177,0.177 10 false *f 2,1.5 2.177,1.677 0.177,0.177 10 false *f
*a Retainer
*b Fuel Pipe
*c Nylon Tube
*d Fuel Tube Connector
*e O-ring
*f Claw
V100135

Push
V100136

Pull out
V100137

Pull off


Disengage the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tube connector from the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



e.

Quick Type B:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A303816C02
1.958,1.531 2.365,1.531 false 1.958,1.281 2.365,1.281 false 2.781,1.271 3.188,1.271 false 1.781,1.448 2.094,1.604 0.313,0.156 10 false *a 1.823,1.198 2.135,1.354 0.313,0.156 10 false *b 3.24,1.208 3.427,1.365 0.188,0.156 10 false *b
*a Retainer
*b Claw
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

Connect the fuel lines and push in the retainer to engage the 2 claws. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




f.

Quick Type C:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A297035C03
0.219,0.49 0.219,0.229 0.219,0.229 0.292,0.229 false 0.875,0.521 0.927,0.302 0.927,0.302 1,0.302 false 0.229,1.031 0.229,0.813 false 0.333,0.146 0.646,0.302 0.313,0.156 10 false *d 1.073,0.208 1.385,0.365 0.313,0.156 10 false *b 0.313,1.323 0.625,1.479 0.313,0.156 10 false *c 0.146,1.042 0.458,1.198 0.313,0.156 10 false *a
*a Fuel Tube Connector
*b Fuel Pipe
*c Retainer
*d O-ring
V100135

Pinch
V100136

Pull off


Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has an O-ring that seals the pipe (fuel pipe).




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



g.

Quick Type C:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A320802C01
1.729,1.396 1.885,1.594 0.156,0.198 10 false .
V100135

Pull


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




h.

Quick Type D:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A268444C02
1.208,2.833 0.99,2.833 false 2.427,2.833 2.229,3.031 2.229,3.031 2.146,3.031 false 0.781,2.75 1.052,2.938 0.271,0.188 10 false *a 1.938,2.958 2.219,3.135 0.281,0.177 10 false *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the fuel tube connector.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.
A308190C01
1.719,2.052 1.719,1.667 false 1.5,2.052 1.875,2.052 1.875,2.052 1.875,1.656 false 2.083,1.177 1.969,0.729 1.969,0.729 1.813,0.729 false 2.26,1.26 2.385,0.76 2.385,0.76 2.521,0.76 false 2.802,1.938 2.635,1.938 2.635,1.938 2.323,1.583 false 2.573,0.667 2.885,0.823 0.313,0.156 10 false *a 1.313,1.958 1.625,2.115 0.313,0.156 10 false *b 1.656,0.635 1.969,0.792 0.313,0.156 10 false *c 2.844,1.844 3.177,2 0.333,0.156 10 false *d
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Pipe


If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



i.

Quick Type D:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A308191C01
0.927,3.104 1.073,3.104 1.073,3.104 1.24,2.854 false 2.052,2.729 2.406,2.729 false 0.76,3.01 1.073,3.167 0.313,0.156 10 false *a 1.875,2.646 2.188,2.802 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

Connect the fuel lines and push in the retainer. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




j.
A289951C03
2.333,0.427 2.521,0.427 2.521,0.427 2.823,0.74 false 0.917,1.615 1.104,1.615 1.104,1.615 1.365,1.333 false 1.708,1.281 1.906,1.594 1.906,1.594 2.052,1.594 false 2.156,0.354 2.448,0.594 0.292,0.24 10 *a 2.115,1.531 2.438,1.792 0.323,0.26 10 *b 0.698,1.563 1,1.823 0.302,0.26 10 *c
*a Fuel Tube Connector
*b Nylon Tube
*c Ethylene Propylene Diene Monomer (EPDM) Rubber Protector


Observe the following precautions when handling a nylon tube:

NOTICE:
·

Do not twist the nylon tube of the fuel tube connector or fuel tube connector when connecting it.

·

Do not remove the Ethylene Propylene Diene Monomer (EPDM) rubber protector on the outside of the nylon tube.

·

Do not bend, twist, pinch or kink the nylon tube.





FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


NOTICE:
A217141C08
1.208,0.938 1.073,0.76 1.073,0.76 0.896,0.76 false 0.688,0.708 1,0.865 0.313,0.156 10 false *a
*a Tube


·

Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.

·

When replacing the fuel filter, replace it together with the fuel suction plate sub-assembly.




INSPECT FOR FUEL LEAK


a.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION