Home › Drivetrain › GF1A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL AWD SYSTEM › 2016.10–2019.09
RM32H0E _52 Drivetrain _059725 GF1A TRANSFER / 4WD / AWD _0298220 DYNAMIC TORQUE CONTROL AWD SYSTEM C

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL AWD SYSTEM  C1297/97  Steering Angle Sensor  


DESCRIPTION

·

The 4WD ECU assembly determines that the vehicle is turning based on the signals sent from the steering sensor.

·

The steering angle sensor signal is sent to the 4WD ECU assembly via the CAN communication system.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1297/97 Steering Angle Sensor When voltage of 4WD ECU assembly IG terminal is 9.5 V or more, and steering sensor malfunction signal is received.
·

ECU-DCC NO. 1 Fuse

·

Steering sensor

·

CAN communication system

·

4WD ECU assembly

·

Wire harness and connector



WIRING DIAGRAM

C367132E02
1.396,1.188 2.625,1.354 1.229,0.167 10 false ECU-IG1 NO. 2 1.323,1.927 2.552,2.094 1.229,0.167 10 false ECU-DCC NO. 1 0.844,3.271 3.073,3.521 2.229,0.25 10 false : CAN Communication Line 3.677,3 5.125,3.292 1.448,0.292 10 false Steering Sensor 5.583,2.167 7.156,2.417 1.573,0.25 10 false 4WD ECU Assembly 3.688,2.844 4.167,3.01 0.479,0.167 10 false F69 3.635,0.927 4.115,1.094 0.479,0.167 10 false 4 3.635,1.656 4.115,1.823 0.479,0.167 10 false 5 3.646,2.333 4.125,2.5 0.479,0.167 10 false 1 3.813,1.042 4.292,1.208 0.479,0.167 10 false IG1 3.813,1.792 4.292,1.958 0.479,0.167 10 false BAT 3.823,2.469 4.302,2.635 0.479,0.167 10 false ESS

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTC.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Clear DTCs
50002 118

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTC(s) is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


d.

Start the engine.


e.

Drive the vehicle at a speed of 35 km/h (24 mph), turn the steering wheel to the right and left and check that no brake control system (steering angle sensor) DTC (C1432, C1433 or C1434) is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105
Result:
Result Proceed to
Neither CAN communication system DTC nor brake control system DTC is output A
CAN communication system DTC is output B


HINT:

When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.




A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
B155846C06
1.469,0.5 1.969,0.75 0.5,0.25 2.031,1.521 2.25,0.833 2.25,0.833 2.417,0.833 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 1.594,0.521 2.063,0.708 0.469,0.188 10 false F69 2.458,0.75 2.917,0.948 0.458,0.198 10 false BAT
*a Front view of wire harness connector
(to Steering Sensor)


Remove the steering wheel and the column cover lower.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the steering sensor connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F69-5 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (IG TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (IG TERMINAL)
a.

Turn the ignition switch to ON.


b.
C368527C01
0.333,1.167 0.833,1.417 0.5,0.25 1.583,1.917 1.865,1.479 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.469,1.177 0.948,1.427 0.479,0.25 10 false F69 1.479,1.938 1.979,2.135 0.5,0.198 10 false IG1
*a Front view of wire harness connector
(to Steering Sensor)


Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
F69-4 (IG1) - Body ground Ignition switch ON 11 to 14 V


Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

4.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)

C

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.
B155846C07
1.469,0.5 1.969,0.75 0.5,0.25 1.417,1.542 1.042,0.823 1.042,0.823 0.792,0.823 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 1.594,0.521 2.021,0.708 0.427,0.188 10 false F69 0.406,0.74 0.719,0.938 0.313,0.198 10 false ESS
*a Front view of wire harness connector
(to Steering Sensor)


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F69-1 (ESS) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (STEERING ANGLE VALUE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (STEERING ANGLE VALUE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Four Wheel Drive / Data List.


e.

Read the value displayed on the GTS.

Chassis > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Angle Value Steering angle value Min.: -3276.8°
Max.: 3276.7°
Left turn: Increase
Right turn: Decrease
Changes in proportion with the amount of steering wheel rotation during steering operation.
Chassis > Four Wheel Drive > Data List
Tester Display
Steering Angle Value
50003 118 8
OK:

The steering angle sensor value changes in accordance with the steering wheel movement.



Result:
Proceed to
OK
NG



OK

NG