If a malfunction in the power source circuit occurs, or a malfunction in communication with the skid control ECU (brake actuator assembly) or in a speed sensor occurs, the 4WD ECU assembly will prohibit operations by the fail-safe function.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1241/94 | Low Power Supply Voltage | 1.
When the following continues for 10 seconds or more: -
At a vehicle speed of 3 km/h (2 mph) or more, voltage of IG1 terminal is 9.5 V or less. 2.
When either of the following is detected: -
With the IG1 terminal voltage 9.5 V or less, communication with the skid control ECU (brake actuator assembly) is impossible. -
Vehicle speed sensor voltage is reduced for 60 seconds or more. 3.
When the following continues for 3 seconds or more: -
With the IG1 terminal voltage 17 V or more, communication with the skid control ECU (brake actuator assembly) is impossible. |
·
Battery ·
Charging system ·
Wire harness and connector (IG1 circuit, GND circuit) ·
Brake control system ·
CAN communication system ·
4WD ECU assembly |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | - | - | - | - |
| Malfunction Status | At a vehicle speed of 3 km/h (2 mph) or more, voltage of IG1 terminal is 9.5 V or less. | ○ | - | - |
| With the IG1 terminal voltage 9.5 V or less, communication with the skid control ECU (brake actuator assembly) is impossible. | - | ○ | - | |
| With the IG1 terminal voltage 17 V or more, communication with the skid control ECU (brake actuator assembly) is impossible. | - | - | ○ | |
| Detection Time | 10 seconds or more | 60 seconds or more | 3 seconds or more | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
Check the condition of each related circuit connector before troubleshooting.
Check if CAN communication system DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Start the engine.
Drive the vehicle, accelerate to a speed of 3 km/h (2 mph) or more for 60 seconds or more, and check if the speed sensor DTC (brake control system DTC) is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Neither CAN communication system DTC nor speed sensor DTC (brake control system DTC) is output | A |
| CAN communication system DTC is output | B |
| Speed sensor DTC (brake control system DTC) is output | C |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
Check the battery voltage.
11 to 14 V
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to 4WD ECU Assembly) |
Disconnect the 4WD ECU assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M77-3 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
| *a | Front view of wire harness connector
(to 4WD ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M77-4 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTC.
Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle, accelerate to a speed of 3 km/h (2 mph) or more, and check if the same DTC is output.
Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC is output | A |
| DTC is not output | B |
Reinstall the sensor, connectors, etc. and restore the vehicle to its prior condition before rechecking DTCs.
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING