Home › Brake › BRAKE (REAR) › REAR BRAKE › 2016.10–2018.05
RM32H0E _54 Brake _060042 BRAKE (REAR) _0298571 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42431 1.INSTALL REAR DISC

a.
C366010C03
0.99,1.927 1.51,1.5 true 0.979,1.927 1.49,1.448 true 0.823,1.854 1.135,2.01 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks of the rear disc and rear axle hub and bearing assembly, and install the rear disc.

NOTICE:

When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.



Hide 2.INSTALL REAR DISC BRAKE CYLINDER MOUNTING

a.

Install the rear disc brake cylinder mounting to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)


Hide 3.INSTALL REAR DISC BRAKE BUSHING DUST BOOT

a.
C366014C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.

HINT:

Apply more than 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bushing dust boot.



b.

Install the 2 rear disc brake bushing dust boots to the rear disc brake cylinder mounting.


Hide 4.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C366015C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the rear No. 2 disc brake cylinder slide pin.


b.

Install a new rear disc brake cylinder slide bushing to the rear No. 2 disc brake cylinder slide pin.


c.
C366016C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin.


d.
C366006C03
1.792,0.313 2.125,0.313 true 1.583,1.052 1.917,1.052 true 1.958,0.979 2.167,1.156 0.208,0.177 10 true *1 2.167,0.229 2.365,0.417 0.198,0.188 10 true *2
*1 Rear No. 1 Disc Brake Cylinder Slide Pin
*2 Rear No. 2 Disc Brake Cylinder Slide Pin


Install the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin to the rear disc brake cylinder mounting.


e.

Push the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin into each rear disc brake bushing dust boot to engage the pins to the boots.


Hide 5.INSTALL REAR DISC BRAKE PAD SUPPORT PLATE

a.

Install the 4 rear disc brake pad support plates to the rear disc brake cylinder mounting.

NOTICE:

Be sure to install each rear disc brake pad support plate in the correct position and direction.



Hide 6.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM

Hide 7.INSTALL REAR DISC BRAKE PAD

a.

Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:

Install the rear disc brake pad so that the rear disc brake pad wear indicator plate is mounted on the lower side of the vehicle.


HINT:
C366020C01
0.833,1.021 1.365,1.021 false 2.052,0.813 2.583,0.813 false 2.635,0.719 2.948,0.875 0.313,0.156 10 false *a 0.625,0.938 0.938,1.094 0.313,0.156 10 false *b
*a Inner Side (Brown)
*b Outer Side (Green)


If the rear disc brake pad has an identification mark, be sure to confirm the installation location.



Hide 8.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C369992C01
0.896,2.854 1.208,3.01 0.313,0.156 10 false *a 1.698,2.771 2.01,2.927 0.313,0.156 10 false *b 1.75,1.844 1.906,2.042 0.156,0.198 10 true 1 2.219,0.438 2.375,0.635 0.156,0.198 10 true 2
*a Hold
*b Turn


Hold the 2 rear disc brake cylinder slide pins, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 new bolts in the order shown in the illustration.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 46310B 9.INSTALL PARKING BRAKE ACTUATOR ASSEMBLY

a.

Apply a light coat of lithium soap base glycol grease to a new O-ring.


b.

Install the O-ring to the rear disc brake cylinder assembly.

NOTICE:

Make sure to replace the O-ring with a new one when installing the parking brake actuator assembly.



c.

Using a 5 mm hexagon socket wrench, install the parking brake actuator assembly to the rear disc brake cylinder assembly with the 2 bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 890C0A 10.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.

Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.


Hide 47319F 11.CONNECT REAR FLEXIBLE HOSE

a.

Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
30.4 N*m (310 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly.



Hide 12. BLEED BRAKE LINE

Hide 13.BLEED REAR DISC BRAKE CYLINDER ASSEMBLY

CAUTION:

If the rear disc brake cylinder assembly has been disassembled, perform air bleeding for the rear disc brake cylinder.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

While performing air bleeding of the rear disc brake assembly, the bolt can be reused during the bleeding procedure. After air bleeding is complete, replace the bolt with a new one.



a.
C369767C01
1.771,2.438 2.083,2.594 0.313,0.156 10 false *a 1.01,2.531 1.323,2.688 0.313,0.156 10 false *b
*a Turn
*b Hold


Perform the procedure to enter rear disc brake pad replacement mode 5 times.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>TEST MODE PROCEDURE


b.

Remove the bolt and separate the rear disc brake cylinder assembly.*1

NOTICE:

Keep the rear no. 2 disc brake cylinder slide pin free of foreign matter.



c.
C368001

Hold the rear disc brake cylinder assembly horizontally, then tilt it 45° toward the bleeder plug side as shown in the illustration.*2


d.
C369768C01
1.813,2.448 2.125,2.604 0.313,0.156 10 false *a 1.021,2.479 1.333,2.635 0.313,0.156 10 false *b
*a Turn
*b Hold


Temporarily install the rear disc brake cylinder assembly with the bolt.*3


e.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*4


f.

When fluid stops coming out, tighten the bleeder plug and release the brake pedal.*5


g.

Repeat steps *1 and *5 until all the air in the brake fluid is completely bled out and new brake fluid comes out.


h.

Tighten the bleeder plug completely.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


i.

Repeat the above 3 steps to replace the brake fluid of the brake tubes for rear wheel.


j.

Install the rear disc brake cylinder assembly with a new bolt.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 14.INSTALL REAR WHEEL