Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System with Top-mounted Air Conditioner Pressure Sensor)
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0298707 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System with Top-mounted Air Conditioner Pressure Sensor) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System with Top-mounted Air Conditioner Pressure Sensor)  PTC Heater Circuit  


DESCRIPTION

The air conditioning amplifier assembly sends operation signals to the PTC heater relays when quick heater assembly operation conditions are met. Based on the signals from the air conditioning amplifier assembly, the PTC heater relays turn on, and power is supplied to the quick heater assembly installed in the air conditioning radiator assembly.

Quick Heater Assembly Operation Condition
Control ECU Condition
Air Conditioning Amplifier Assembly Ignition switch ON
ECO mode: off
Blower switch: On
Temperature setting: MAX HOT
Light control switch off
·

Engine coolant temperature 65°C (149°F) or lower (3 PTC heater relays operating)

·

Engine coolant temperature 70°C (158°F) or lower (2 PTC heater relays operating)

·

Engine coolant temperature 75°C (167°F) or lower (1 PTC heater relay operating)


·

Ambient temperature -7°C (19°F) or lower (3 PTC heater relays operating)

·

Ambient temperature 16°C (61°F) or lower (2 PTC heater relays operating)

·

Ambient temperature 25°C (77°F) or lower (1 PTC heater relay operating)



WIRING DIAGRAM

E357652E05
0.073,0.542 1.646,0.979 1.573,0.438 10 false from IG1-NO. 1 Relay 0.646,1.021 1.51,1.281 0.865,0.26 10 false from Battery 1.875,0.74 2.885,0.958 1.01,0.219 10 false ECU-IG1 NO. 3 1.896,2.396 2.906,2.615 1.01,0.219 10 false PTC HTR NO. 2 1.885,1.229 2.896,1.448 1.01,0.219 10 false PTC HTR NO. 1 1.896,3.594 2.906,3.813 1.01,0.219 10 false PTC HTR NO. 3 3.531,2.479 4.542,2.698 1.01,0.219 10 false PTC HTR NO. 2 3.531,1.323 4.542,1.542 1.01,0.219 10 false PTC HTR NO. 1 3.51,3.698 4.521,3.917 1.01,0.219 10 false PTC HTR NO. 3 3.469,0.469 3.688,0.708 0.219,0.24 10 false 1 3.479,0.938 3.656,1.135 0.177,0.198 10 false 3 4.479,0.448 4.656,0.646 0.177,0.198 10 false 2 4.479,0.927 4.656,1.125 0.177,0.198 10 false 5 5.552,0.458 5.729,0.656 0.177,0.198 10 false 19 5.583,1.646 5.76,1.844 0.177,0.198 10 false 39 5.813,1.625 6.313,1.823 0.5,0.198 10 false PTC2 5.813,0.479 6.313,0.677 0.5,0.198 10 false PTC1 5.833,2.823 6.333,3.021 0.5,0.198 10 false PTC3 5.583,2.813 5.76,3.01 0.177,0.198 10 false 20 3.479,1.635 3.698,1.875 0.219,0.24 10 false 1 3.479,2.104 3.656,2.302 0.177,0.198 10 false 3 4.49,1.646 4.667,1.844 0.177,0.198 10 false 2 4.479,2.104 4.656,2.302 0.177,0.198 10 false 5 4.469,3.302 4.646,3.5 0.177,0.198 10 false 5 4.479,2.823 4.656,3.021 0.177,0.198 10 false 2 3.458,2.833 3.677,3.073 0.219,0.24 10 false 1 3.479,3.302 3.656,3.5 0.177,0.198 10 false 3 4.417,4.021 4.594,4.219 0.177,0.198 10 false 5 3.125,4.052 3.302,4.25 0.177,0.198 10 false 4 3.104,5.083 3.281,5.281 0.177,0.198 10 false 2 4.438,5.063 4.615,5.26 0.177,0.198 10 false 3 4.427,4.448 4.604,4.646 0.177,0.198 10 false 1 3.021,5.344 3.25,5.542 0.229,0.198 10 false H2 3.021,5.5 4.76,5.698 1.74,0.198 10 false Quick Heater Assembly 5.438,3.656 5.875,3.885 0.438,0.229 10 false F72 5.417,3.802 7.052,4.271 1.635,0.469 10 false Air Conditioning Amplifier Assembly 3.292,4.073 3.448,4.271 0.156,0.198 10 false E 3.292,5.083 3.448,5.281 0.156,0.198 10 false E 4.229,4.052 4.385,4.25 0.156,0.198 10 false B 4.24,4.469 4.396,4.667 0.156,0.198 10 false B 4.24,5.073 4.396,5.271 0.156,0.198 10 false B

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (HEATER ACTIVE LEVEL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Heater Active Level Quick heater assembly Min.: 0, Max.: 3 -
Body Electrical > Air Conditioner > Active Test
Tester Display
Heater Active Level
50004 121 33
OK:

Heater Active Level changes normally.



Result:
Proceed to
OK
NG



OK

2.INSPECT PTC HEATER RELAY

NG

2.INSPECT PTC HEATER RELAY
a.

Remove the PTC heater relays.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - POWER SOURCE)

NG

REPLACE PTC HEATER RELAY

3.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - POWER SOURCE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
PTC HTR NO. 1:
Tester Connection Switch Condition Specified Condition
Relay terminal 3 - Body ground Always 11 to 14 V
Relay terminal 1 - Body ground Ignition switch off Below 1 V
Relay terminal 1 - Body ground Ignition switch ON 11 to 14 V


Standard Voltage:
PTC HTR NO. 2:
Tester Connection Switch Condition Specified Condition
Relay terminal 3 - Body ground Always 11 to 14 V
Relay terminal 1 - Body ground Ignition switch off Below 1 V
Relay terminal 1 - Body ground Ignition switch ON 11 to 14 V


Standard Voltage:
PTC HTR NO. 3:
Tester Connection Switch Condition Specified Condition
Relay terminal 3 - Body ground Always 11 to 14 V
Relay terminal 1 - Body ground Ignition switch off Below 1 V
Relay terminal 1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F72 air conditioning amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
PTC HTR NO. 1:
Tester Connection Condition Specified Condition
Relay terminal 2 - F72-19 (PTC1) Always Below 1 Ω
Relay terminal 2 or F72-19 (PTC1) - Body ground Always 10 kΩ or higher


Standard Resistance:
PTC HTR NO. 2:
Tester Connection Condition Specified Condition
Relay terminal 2 - F72-39 (PTC2) Always Below 1 Ω
Relay terminal 2 or F72-39 (PTC2) - Body ground Always 10 kΩ or higher


Standard Resistance:
PTC HTR NO. 3:
Tester Connection Condition Specified Condition
Relay terminal 2 -F72-20 (PTC3) Always Below 1 Ω
Relay terminal 2 or F72-20 (PTC3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - QUICK HEATER ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - QUICK HEATER ASSEMBLY AND BODY GROUND)
a.

Disconnect the H2 quick heater assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
PTC HTR NO. 1:
Tester Connection Condition Specified Condition
Relay terminal 5 - H2-3 (B) Always Below 1 Ω
H2-2 (E) - Body ground Always Below 1 Ω
H2-4 (E) - Body ground Always Below 1 Ω
Relay terminal 5 or H2-3 (B) - Body ground Always 10 kΩ or higher


Standard Resistance:
PTC HTR NO. 2:
Tester Connection Condition Specified Condition
Relay terminal 5 - H2-1 (B) Always Below 1 Ω
H2-2 (E) - Body ground Always Below 1 Ω
Relay terminal 5 or H2-1 (B) - Body ground Always 10 kΩ or higher


Standard Resistance:
PTC HTR NO. 3:
Tester Connection Condition Specified Condition
Relay terminal 5 - H2-5 (B) Always Below 1 Ω
H2-4 (E) - Body ground Always Below 1 Ω
Relay terminal 5 or H2-5 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT QUICK HEATER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT QUICK HEATER ASSEMBLY
a.

b.

Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG