Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2016.10–2020.08
RM32H0E _58 Vehicle Interior _059622 PRE-COLLISION _0298842 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  C1A46  Yaw Rate Sensor  


DESCRIPTION

The millimeter wave radar sensor assembly receives yaw rate and acceleration sensor (airbag sensor assembly) signals from the airbag sensor assembly and skid control ECU (brake actuator assembly) via CAN communication. If the millimeter wave radar sensor assembly receives yaw rate and acceleration sensor (airbag sensor assembly) malfunction signals from the airbag sensor assembly or skid control ECU (brake actuator assembly), DTC C1A46 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A46 Yaw Rate Sensor Any of the following conditions is met:
·

While the vehicle is being driven at a speed of 5 km/h (4 mph) or more, the millimeter wave radar sensor assembly receives a yaw rate and acceleration sensor (airbag sensor assembly) malfunction signals from yaw rate and acceleration sensor (airbag sensor assembly) for approximately 10 seconds.

·

While the vehicle is being driven at a speed of 5 km/h (4 mph) or more, the millimeter wave radar sensor assembly receives a yaw rate and acceleration sensor (airbag sensor assembly) zero point malfunction signals from skid control ECU (brake actuator assembly) for approximately 1 second.


·

Vehicle stability control system

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake actuator assembly)

·

Millimeter wave radar sensor assembly



DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition While the vehicle is being driven at a speed of 5 km/h (4 mph) or more. ○ ○
Malfunction Status The millimeter wave radar sensor assembly receives a yaw rate and acceleration sensor (airbag sensor assembly) malfunction signals from yaw rate and acceleration sensor (airbag sensor assembly). ○ -
The millimeter wave radar sensor assembly receives a yaw rate and acceleration sensor (airbag sensor assembly) zero point malfunction signals from skid control ECU (brake actuator assembly). - ○
Detection Time 10 seconds 1 second
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

The pre-collision system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)
HINT:

Pre-collision system DTC C1A46 may be stored due to a malfunction in the VSC system. Therefore, it is necessary to check for and troubleshoot VSC system DTCs first.


a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105

Result:
Result Proceed to
Vehicle stability control system DTCs are not output A
Vehicle stability control system DTCs are output B



A

2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)

B

2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A46 is not output A
DTC C1A46 is output B



A

B

3.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
3.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
4.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A46 is not output A
DTC C1A46 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

5.REPLACE YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)
5.REPLACE YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)
a.

Replace the yaw rate and acceleration sensor (airbag sensor assembly).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
6.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A46 is not output A
DTC C1A46 is output (for LHD) B
DTC C1A46 is output (for RHD) C



A

END (YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY) WAS DEFECTIVE)

B

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

C

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)