Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2016.10–2020.08
RM32H0E _58 Vehicle Interior _059622 PRE-COLLISION _0298842 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  


DESCRIPTION

The millimeter wave radar sensor assembly is connected to the skid control ECU (brake actuator assembly) by a CAN communication line.

When entering test mode, the skid control ECU (brake actuator assembly) communicates with the millimeter wave radar sensor assembly and determines whether the vehicle is equipped with a pre-collision system.

U023A is output when it is determined that the vehicle is not equipped with a pre-collision system.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0235 Lost Communication with Cruise Control Front Distance Range Sensor When entering test mode, the skid control ECU (brake actuator assembly) determines that the vehicle is not equipped with a pre-collision system
·

Skid control ECU (Brake actuator assembly)

·

Millimeter wave radar sensor assembly

·

Wire harness or connector



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

The pre-collision system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U0235 and other DTCs are output A
Only DTC U0235 is output B



A

B

2.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)
2.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105

Result:
Result Proceed to
Vehicle stability control system DTC are not output A
Vehicle stability control system DTC are output B



A

3.TEST MODE INSPECTION (VEHICLE STABILITY CONTROL SYSTEM)

B

3.TEST MODE INSPECTION (VEHICLE STABILITY CONTROL SYSTEM)
HINT:

When entering test mode, the skid control ECU (brake actuator assembly) communicates with the millimeter wave radar sensor assembly to judge whether the vehicle is equipped with the pre-collision system. Therefore, do not exit test mode within 5 seconds of entering test mode.


a.

Procedure to Enter Test Mode (Signal Check)

i.

Turn the ignition switch to ON.


ii.

for Manual Transmission:

Check that the shift lever is in neutral and apply the parking brake.

for Automatic Transmission:

Check that the shift lever is in P and apply the parking brake.


iii.

Put the steering wheel in the neutral position.


iv.

Connect the GTS to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the GTS on.


vii.

Switch the skid control ECU (brake actuator assembly) to Test Mode (Signal Check) using the GTS. Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Utility / Signal Check.

HINT:

Do not exit test mode within 5 seconds of entering test mode. If test mode is exited within 5 seconds of entering test mode, DTC U0235 may be stored. If DTC U0235 is output after exiting test mode, enter test mode again, wait at least 5 seconds, then recheck for DTCs.


Chassis > ABS/VSC/TRC/EPB > Utility
Tester Display
Signal Check
50005 105 4359


b.

Test Mode (Signal Check) Display Check

i.

Check that the ABS warning and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.

HINT:

If the ABS warning and slip indicator lights remains illuminated or does not illuminate when Test Mode (Signal Check) is entered, a component or wire harness may be malfunctioning.




c.

End of Test Mode (Signal Check)

i.

Turn the ignition switch off and disconnect the GTS.



Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
4.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U0235 is not output A
DTC U0235 is output B



A

END

B

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
6.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U0235 is not output A
DTC U0235 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

7.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
7.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
a.

Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC (PRE-COLLISION SYSTEM)
8.CLEAR DTC (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

Result:
Proceed to
NEXT



NEXT

END (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) WAS DEFECTIVE)