Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2016.10–2018.05
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299013 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate  


DESCRIPTION

If the entry lock and wireless door lock operations cannot be performed, the door control receiver may be malfunctioning, or there may be wave interference or problems in the communication which is used for the entry and wireless function between the door control receiver and certification ECU (smart key ECU assembly).

WIRING DIAGRAM

E352040E02
0.229,0.438 3.75,0.635 3.521,0.198 10 false from ECU-DCC NO. 2 Fuse 1.156,0.99 4.677,1.188 3.521,0.198 10 false from Battery 1.01,1.563 4.531,1.76 3.521,0.198 10 false to ACC Relay 1.073,2.177 4.594,2.375 3.521,0.198 10 false to IG1 Relay 0.323,2.823 3.844,3.021 3.521,0.198 10 false from ECU-IG1 NO. 4 Fuse 3.417,1.208 6.938,1.406 3.521,0.198 10 false AM2 0.667,7.74 2.323,8.333 1.656,0.594 10 false Main Body ECU (Multiplex Network Body ECU) 0.729,8.448 4.25,8.646 3.521,0.198 10 false : CAN Communication Line 0.667,6.146 1.833,6.333 1.167,0.188 10 false M23*1, M30*2 0.656,6.313 2.25,6.885 1.594,0.573 10 false Electrical Key and TPMS Receiver Assembly 5.146,8.094 6.958,8.698 1.813,0.604 10 false Certification ECU (Smart Key ECU Assembly) 0.906,4.667 1.219,4.865 0.313,0.198 10 false IC 6.24,1.719 6.552,1.917 0.313,0.198 10 false IC 5.292,6.208 5.604,6.406 0.313,0.198 10 false E 1.885,3.969 2.198,4.167 0.313,0.198 10 false +5 1.698,4.594 2.177,4.833 0.479,0.24 10 false DATA 1.698,5.198 2.208,5.469 0.51,0.271 10 false CSEL 1.729,5.76 2.104,6.052 0.375,0.292 10 false GND 2.156,5.656 2.469,5.854 0.313,0.198 10 false 1*2 2.156,5.198 2.469,5.396 0.313,0.198 10 false 2*2 2.146,4.594 2.458,4.792 0.313,0.198 10 false 5*2 2.146,3.969 2.458,4.167 0.313,0.198 10 false 4*2 2.135,3.479 2.448,3.677 0.313,0.198 10 false 1*1 4.938,6.219 5.25,6.417 0.313,0.198 10 false F1 4.938,0.448 5.25,0.646 0.313,0.198 10 false F1 4.948,1.01 5.26,1.208 0.313,0.198 10 false F1 4.938,1.573 5.25,1.771 0.313,0.198 10 false F1 4.948,2.198 5.26,2.396 0.313,0.198 10 false F1 5.281,0.438 5.823,0.74 0.542,0.302 10 false CUTB 5.26,2.073 5.802,2.375 0.542,0.302 10 false IG1D 5.26,1.448 5.802,1.75 0.542,0.302 10 false ACCD 5.281,1 5.823,1.302 0.542,0.302 10 false +B 5.781,1.677 6.323,1.979 0.542,0.302 10 false +B 5.792,1.042 6.333,1.344 0.542,0.302 10 false +B 4.948,0.219 5.49,0.521 0.542,0.302 10 false 15 4.958,0.792 5.5,1.094 0.542,0.302 10 false 4 4.938,1.365 5.479,1.667 0.542,0.302 10 false 16 4.99,1.979 5.531,2.281 0.542,0.302 10 false 17 5.802,3.552 6.344,3.854 0.542,0.302 10 false 5V 4.917,4.083 5.458,4.385 0.542,0.302 10 false M67 5.792,4.198 6.333,4.5 0.542,0.302 10 false +B 5.792,4.813 6.333,5.115 0.542,0.302 10 false +B 4.906,4.698 5.448,5 0.542,0.302 10 false M67 4.906,5.313 5.448,5.615 0.542,0.302 10 false M67 4.938,3.865 5.479,4.167 0.542,0.302 10 false 18 4.948,4.469 5.49,4.771 0.542,0.302 10 false 19 4.938,5.104 5.479,5.406 0.542,0.302 10 false 20 4.938,6.01 5.479,6.313 0.542,0.302 10 false 18 5.26,3.969 5.802,4.271 0.542,0.302 10 false RCO 5.26,4.573 5.802,4.875 0.542,0.302 10 false RDAM 5.25,5.208 5.792,5.51 0.542,0.302 10 false CSEL 1.865,3.563 2.177,3.76 0.313,0.198 10 false IG 2.583,7.844 6.104,8.042 3.521,0.198 10 false *1: w/ Tire Pressure Warning System 2.594,8.219 6.115,8.417 3.521,0.198 10 false *2: w/o Tire Pressure Warning System 2.146,3.781 2.458,3.979 0.313,0.198 10 false 8*1 2.146,4.385 2.458,4.583 0.313,0.198 10 false 2*1 2.156,5.031 2.469,5.229 0.313,0.198 10 false 6*1 2.135,5.49 2.448,5.688 0.313,0.198 10 false 12*1

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

·

When replacing the electrical key & TPMS receiver assembly, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.*1

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION

*1: w/ Tire Pressure Warning System


·

It is necessary to perform initialization (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the electrical key & TPMS receiver assembly if the electrical key & TPMS receiver assembly has been replaced.*1

*1: w/ Tire Pressure Warning System




PROCEDURE

1.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage with the engine switch off.

Standard Voltage:

11 to 14 V


HINT:

It may be possible to tell whether the battery is discharged by operating the horn.

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.


b.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CHECK DOOR AJAR WARNING

B

3.CHECK DOOR AJAR WARNING
a.

When the doors are locked by operating the entry lock function with all doors closed, check that the door ajar warning operates.

HINT:

Warning function (door ajar warning)

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>SYSTEM DESCRIPTION



Result:
Result Proceed to
The wireless buzzer does not sound A
The wireless buzzer sounds B



A

4.CHECK POWER DOOR LOCK CONTROL SYSTEM

B

4.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Power door lock function operates normally A
Power door lock function does not operate normally B



A

5.CHECK KEY DIAGNOSTIC MODE

B

5.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
i.
E351993C04
0.083,0.094 0.344,0.323 0.26,0.229 12 false *A 0.094,2.646 0.344,2.875 0.25,0.229 12 false *B 2.229,1.635 2.406,1.823 0.177,0.188 10 false *a 1.292,3.698 1.469,3.885 0.177,0.188 10 false *a
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for driver door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




ii.
E351993C05
0.083,0.094 0.344,0.323 0.26,0.229 12 false *A 0.094,2.646 0.344,2.875 0.25,0.229 12 false *B 2.229,1.635 2.406,1.823 0.177,0.188 10 false *a 1.292,3.698 1.469,3.885 0.177,0.188 10 false *a
*A for RHD
*B for LHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for front passenger door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




iii.
E351995C02
0.573,0.708 2.656,0.281 2.656,0.281 1.938,0.698 true 2.719,0.177 3.031,0.333 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (front floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




iv.
E351996C02
0.573,0.552 2.531,0.188 2.531,0.188 1.906,0.563 true 2.594,0.094 2.906,0.25 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna assembly (rear floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




v.
E351998C02
1.24,1.75 2.479,0.313 2.479,0.313 1.854,1.219 true 2.531,0.219 2.844,0.375 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 3 indoor electrical key antenna assembly (inside luggage compartment):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




vi.
E351997C02
1.771,1.354 2.083,1.51 0.313,0.156 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (outside luggage compartment):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



OK:

Wireless buzzer sounds.




Result:
Result Proceed to
Key diagnostic mode inspections fail for both channels A
Key diagnostic mode inspections succeed for both channels B
Key diagnostic mode inspection succeeds for only one of the channels C



A

6.CHECK WAVE ENVIRONMENT

B

18.PERFORM REGISTRATION

C

28.CHECK WAVE ENVIRONMENT
6.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless operation 2 or more times*.

*: When the wireless function is operated, channel 1 and 2 are used alternately. If the first wireless operation is performed successfully and the second wireless operation fails, wave interference may be occurring for either channel.


HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
Wireless function does not operate normally A
Wireless function operates normally B



A

7.CHECK TRANSMITTER BATTERY

B

AFFECTED BY WAVE INTERFERENCE

7.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the electrical key transmitter sub-assembly for 5 seconds and check the number of times that the LED illuminates.

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly near the engine switch, depressing the brake pedal and pressing the engine switch.





Result:
Result Proceed to
LED illuminates 3 times or more when switch is pressed and held A
LED does not illuminate when switch is pressed and held B
LED illuminates once or twice but not a third time C



A

8.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

17.INSPECT TRANSMITTER BATTERY

C

8.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.


Result:
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B



A

9.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

10.CHECK ENTRY LOCK OPERATION
9.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK ENTRY LOCK OPERATION
10.CHECK ENTRY LOCK OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check that the function operates normally.


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER AND BODY GROUND)

B

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER AND BODY GROUND)
a.

Disconnect the M67 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the M23*1 or M30*2 door control receiver connector.

*1: w/ Tire Pressure Warning System

*2: w/o Tire Pressure Warning System



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M67-18 (RCO) - M23-8 (+5)*1 Always Below 1 Ω
M67-18 (RCO) - M30-4 (+5)*2
M67-19 (RDAM) - M23-2 (DATA)*1 Always Below 1 Ω
M67-19 (RDAM) - M30-5 (DATA)*2
M67-20 (CSEL) - M23-6 (CSEL)*1 Always Below 1 Ω
M67-20 (CSEL) - M30-2 (CSEL)*2
M23-12 (GND) - Body ground*1 Always Below 1 Ω
M30-1 (GND) - Body ground*2
M67-18 (RCO) or M23-8 (+5) - Body ground*1 Always 10 kΩ or higher
M67-18 (RCO) or M30-4 (+5) - Body ground*2
M67-19 (RDAM) or M23-2 (DATA) - Body ground*1 Always 10 kΩ or higher
M67-19 (RDAM) or M30-5 (DATA) - Body ground*2
M67-20 (CSEL) or M23-6 (CSEL) - Body ground*1 Always 10 kΩ or higher
M67-20 (CSEL) or M30-2 (CSEL) - Body ground*2


*1: w/ Tire Pressure Warning System

*2: w/o Tire Pressure Warning System



Result:
Proceed to
OK
NG



OK

12.CHECK ENTRY LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK ENTRY LOCK OPERATION
a.

Connect all connectors and check that the entry function operates normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

13.CHECK DOOR CONTROL RECEIVER

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

13.CHECK DOOR CONTROL RECEIVER
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Tire Pressure Warning System
Tester Connection Condition Specified Condition
M23-12 (GND) - Body ground Always Below 1 Ω

w/o Tire Pressure Warning System
Tester Connection Condition Specified Condition
M30-1 (GND) - Body ground Always Below 1 Ω



b.
B423547C08
0.667,0.208 1.063,0.469 0.396,0.26 2.365,0.208 2.76,0.469 0.396,0.26 0.375,2.021 0.594,1.354 true 1.417,2.042 1.135,1.208 true 3.052,2 2.823,1.177 true 2.156,2 2.198,1.177 true 2.427,0.26 2.74,0.458 0.313,0.198 10 false M30 1.26,2.063 1.781,2.406 0.521,0.344 10 false DATA 0.219,2.052 0.74,2.396 0.521,0.344 10 false GND 0.292,0.354 0.604,0.552 0.313,0.198 10 false *a 0.729,2.313 1.042,2.51 0.313,0.198 10 false *b 0.188,3.24 0.656,3.5 0.469,0.26 10 false GND 1.01,4.156 1.323,4.354 0.313,0.198 10 false *c 2.219,4.167 2.531,4.365 0.313,0.198 10 false *d 1.854,0.385 2.177,0.583 0.323,0.198 10 false *a 0.74,0.25 1.052,0.448 0.313,0.198 10 false M23 2.01,2.031 2.531,2.375 0.521,0.344 10 false DATA 2.906,2.042 3.427,2.385 0.521,0.344 10 false GND 0.104,0.073 0.417,0.271 0.313,0.198 10 false *A 1.813,0.073 2.125,0.271 0.313,0.198 10 false *B
*A w/ Tire Pressure Warning System
*B w/o Tire Pressure Warning System
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1
*c Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*d After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check the waveform.

OK:
w/ Tire Pressure Warning System
Tester Connection Condition Tool Setting Specified Condition
M23-2 (DATA) - M23-12 (GND) Procedure:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms/DIV. Below 1 V → Pulse generation
(See waveform 1)

w/o Tire Pressure Warning System
Tester Connection Condition Tool Setting Specified Condition
M30-5 (DATA) - M30-1 (GND) Procedure:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms/DIV. Below 1 V → Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DOOR CONTROL RECEIVER

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B423550C10
1.552,0.219 1.958,0.5 0.406,0.281 1.563,2.292 1.969,2.573 0.406,0.281 0.823,1.771 1.417,1.219 true 1.281,1.875 1.427,1.417 true 2.51,1.833 2.104,1.229 true 2.5,4.094 2.073,3.188 true 1.865,4.094 1.906,3.177 true 0.74,0.135 1.125,0.479 0.385,0.344 10 false *A 0.771,2.208 1.156,2.552 0.385,0.344 10 false *B 1.625,0.271 2.01,0.615 0.385,0.344 10 false M23 1.646,2.354 2.031,2.698 0.385,0.344 10 false M30 1.083,0.385 1.469,0.729 0.385,0.344 10 false *a 1.104,2.417 1.49,2.76 0.385,0.344 10 false *a 0.625,1.802 1.125,2.177 0.5,0.375 10 false CSEL 1.146,1.906 1.646,2.281 0.5,0.375 10 false GND 2.469,1.875 2.969,2.25 0.5,0.375 10 false IG 1.719,4.125 2.219,4.5 0.5,0.375 10 false CSEL 2.375,4.125 2.875,4.5 0.5,0.375 10 false GND
*A w/ Tire Pressure Warning System
*B w/o Tire Pressure Warning System
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Tire Pressure Warning System
Tester Connection Condition Specified Condition
M23-1 (IG) - M23-12 (GND) Engine switch on (IG) 10 to 16 V
M23-6 (CSEL) - M23-12 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → Pulse generation

w/o Tire Pressure Warning System
Tester Connection Condition Specified Condition
M30-2 (CSEL) - M30-1 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → Pulse generation



b.
B423549C05
0.781,0.198 1.146,0.438 0.365,0.24 2.26,0.219 2.625,0.458 0.365,0.24 0.396,2.073 0.625,1.292 true 1.198,2.073 1.156,1.323 true 3.104,1.927 2.771,1.063 true 2.063,1.938 2.281,1.063 true 0.188,0.083 0.5,0.281 0.313,0.198 10 false *A 1.781,0.073 2.094,0.271 0.313,0.198 10 false *B 0.281,2.104 0.74,2.302 0.458,0.198 10 false GND 2.979,1.938 3.375,2.177 0.396,0.24 10 false GND 1.156,2.094 1.615,2.292 0.458,0.198 10 false +5 1.99,1.958 2.448,2.156 0.458,0.198 10 false +5 2.323,0.271 2.781,0.469 0.458,0.198 10 false M30 0.833,0.25 1.292,0.448 0.458,0.198 10 false M23 0.344,0.354 0.604,0.594 0.26,0.24 10 false *a 1.865,0.333 2.125,0.573 0.26,0.24 10 false *a 0.688,2.26 0.948,2.5 0.26,0.24 10 false *b 0.948,4.083 1.208,4.323 0.26,0.24 10 false *c 2.031,4.083 2.292,4.323 0.26,0.24 10 false *d 0.167,3.198 0.625,3.396 0.458,0.198 10 false GND
*A w/ Tire Pressure Warning System
*B w/o Tire Pressure Warning System
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1
*c Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*d After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check the waveform.

OK:
w/ Tire Pressure Warning System
Tester Connection Condition Tool Setting Specified Condition
M23-8 (+5) - M23-12 (GND) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)

w/o Tire Pressure Warning System
Tester Connection Condition Tool Setting Specified Condition
M30-4 (+5) - M30-1 (GND) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

15.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

15.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) and perform registration again.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

16.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
16.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally (for LHD) B
Wireless door lock function does not operate normally (for RHD) C



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

17.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>INSPECTION

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

18.PERFORM REGISTRATION
a.

Perform registration of the B code.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

19.CHECK ENTRY LOCK OPERATION
19.CHECK ENTRY LOCK OPERATION
a.

After completing B code registration, check that the entry lock and unlock functions can be operated 2 times consecutively.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

20.READ VALUE USING GTS (B CODE)

B

END (B CODE REGISTRATION FAILED)

20.READ VALUE USING GTS (B CODE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
B Code B code registration status Regd or No Regd Regd: B code registered correctly
No Regd: B code not registered correctly
-
Body Electrical > Entry&Start > Data List
Tester Display
B Code
50003 125 132

Result:
Result Proceed to
"No Regd" is displayed on the GTS A
"Regd" is displayed on the GTS (for LHD) B
"Regd" is displayed on the GTS (for RHD) C



A

21.READ VALUE USING GTS (B CODE DIFFERENCE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

21.READ VALUE USING GTS (B CODE DIFFERENCE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
B Code Difference B code mismatch Yes or No Yes: Communication malfunction
No: Communication normal
-
Body Electrical > Entry&Start > Data List
Tester Display
B Code Difference
50003 125 131

Result:
Result Proceed to
"No" is displayed on the GTS A
"Yes" is displayed on the GTS B



A

22.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

22.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage while checking the Data List on the GTS.

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control / Data List.


v.

Read the Data List according to the display on the GTS.

B416787C20
4.563,0.469 4.958,0.698 0.396,0.229 4.01,2.188 4.25,1.323 true 4.5,2.198 4.333,1.323 true 4.667,0.49 4.979,0.688 0.313,0.198 10 false F1 3.854,2.229 4.281,2.458 0.427,0.229 10 false IG1D 0.198,0.156 0.51,0.354 0.313,0.198 10 false *a 4.344,2.229 4.802,2.438 0.458,0.208 10 false ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Engine switch off
ACC ON: Engine switch on (ACC)
IG ON: Engine switch on (IG)
ST ON: Sending engine start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18
Standard Voltage:
Tester Connection Switch Condition Specified Condition
F1-17 (IG1D) - Body ground Engine switch off Below 1 V
Engine switch on (ACC) Below 1 V
Engine switch on (IG) 9 V or higher
F1-16 (ACCD) - Body ground Engine switch off Below 1 V
Engine switch on (ACC) 9 V or higher
Engine switch on (IG) 9 V or higher




Result:
Proceed to
OK
NG



OK

23.READ VALUE USING GTS (ACC SW, IG SW)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

23.READ VALUE USING GTS (ACC SW, IG SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Engine switch status ON or OFF ON: Engine switch on (ACC)
OFF: Engine switch off
"ON" is also displayed when the engine switch is on (IG).
IG SW Engine switch status ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
"OFF" is also displayed when the engine switch is on (ACC).
Body Electrical > Main Body > Data List
Tester Display
ACC SW
IG SW
50003 123 31,30
HINT:

If the certification ECU (smart key ECU assembly) misjudges for any reason that the engine switch is on (IG) even though the engine switch is off, the entry lock and unlock functions will be disabled.



Result:
Result Proceed to
The main body ECU (multiplex network body ECU) judges properly that the power source is off when the engine switch is off A
The main body ECU (multiplex network body ECU) does not judge properly that the power source is off when the engine switch is off B



A

24.CHECK HARNESS AND CONNECTOR (BODY GROUND, POWER SUPPLY)

B

24.CHECK HARNESS AND CONNECTOR (BODY GROUND, POWER SUPPLY)
a.
B416821C28
1.448,2.427 1.865,2.677 0.417,0.25 0.938,4.344 1.167,3.802 true 2.406,4.354 2.115,3.677 true 0.531,2.479 0.844,2.635 0.313,0.156 10 false *a 1.542,2.458 1.854,2.615 0.313,0.156 10 false F1 0.875,4.375 1.26,4.615 0.385,0.24 10 false E 2.26,4.365 2.771,4.615 0.51,0.25 10 false CUTB
*a Front view of wire harness connected
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-18 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F1-15 (CUTB) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

25.CHECK ENTRY LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK ENTRY LOCK OPERATION
a.

Disconnect and reconnect the certification ECU (smart key ECU assembly) connectors.



Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

26.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

26.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration again.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

27.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
27.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally (for LHD) B
Wireless door lock function does not operate normally (for RHD) C



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

28.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless operation 2 or more times*.

*: When the wireless function is operated, channel 1 and 2 are used alternately. If the first wireless operation is performed successfully and the second wireless operation fails, wave interference may be occurring for either channel.


HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
Wireless function does not operate normally A
Wireless function operates normally 1 or more times. B



A

29.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

AFFECTED BY WAVE INTERFERENCE

29.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.


Result:
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B



A

30.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

31.CHECK WAVE ENVIRONMENT
30.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

31.CHECK WAVE ENVIRONMENT
31.CHECK WAVE ENVIRONMENT
a.

Bring another registered electrical key transmitter sub-assembly near the door control receiver and perform a wireless operation 2 or more times*.

*: When the wireless function is operated, channel 1 and 2 are used alternately. If the first wireless operation is performed successfully and the second wireless operation fails, wave interference may be occurring for either channel.


HINT:
·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
Wireless function does not operate normally A
Wireless function operates normally 1 or more times. B



A

32.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)

B

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

32.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)
a.

Disconnect the M23*1 or M30*2 door control receiver connector.

*1: w/ Tire Pressure Warning System

*2: w/o Tire Pressure Warning System



b.

Disconnect the M67 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M23-6 (CSEL) - M67-20 (CSEL)*1 Always Below 1 Ω
M30-2 (CSEL) - M67-20 (CSEL)*2
M23-6 (CSEL) or M67-20 (CSEL) - Body ground*1 Always 10 kΩ or higher
M30-2 (CSEL) or M67-20 (CSEL) - Body ground*2


*1: w/ Tire Pressure Warning System

*2: w/o Tire Pressure Warning System



Result:
Proceed to
OK
NG



OK

33.CHECK ENTRY LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.CHECK ENTRY LOCK OPERATION
a.

Connect all connectors and check that the function operates normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

34.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

34.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B423550C11
1.552,0.219 1.958,0.5 0.406,0.281 1.563,2.292 1.969,2.573 0.406,0.281 0.823,1.771 1.417,1.219 true 1.281,1.875 1.427,1.417 true 2.5,4.094 2.073,3.188 true 1.865,4.094 1.906,3.177 true 0.74,0.135 1.125,0.479 0.385,0.344 10 false *A 0.771,2.208 1.156,2.552 0.385,0.344 10 false *B 1.635,0.281 2.021,0.625 0.385,0.344 10 false M23 1.646,2.354 2.031,2.698 0.385,0.344 10 false M30 1.083,0.385 1.469,0.729 0.385,0.344 10 false *a 1.104,2.417 1.49,2.76 0.385,0.344 10 false *a 0.625,1.802 1.125,2.177 0.5,0.375 10 false CSEL 1.146,1.906 1.646,2.281 0.5,0.375 10 false GND 1.719,4.125 2.219,4.5 0.5,0.375 10 false CSEL 2.375,4.125 2.875,4.5 0.5,0.375 10 false GND
*A w/ Tire Pressure Warning System
*B w/o Tire Pressure Warning System
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Tire Pressure Warning System
Tester Connection Condition Specified Condition
M23-6 (CSEL) - M23-12 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → Pulse generation

w/o Tire Pressure Warning System
Tester Connection Condition Specified Condition
M30-2 (CSEL) - M30-1 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → Pulse generation



Result:
Proceed to
OK
NG



OK

35.CHECK DOOR CONTROL RECEIVER

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

35.CHECK DOOR CONTROL RECEIVER
a.

Enter key diagnostic mode and select the channel for which the wireless buzzer did not sound.


b.
B423547C09
0.667,0.208 1.063,0.469 0.396,0.26 2.365,0.208 2.76,0.469 0.396,0.26 0.375,2.031 0.594,1.365 true 1.417,2.042 1.135,1.208 true 3.052,2 2.823,1.177 true 2.156,2 2.198,1.177 true 2.438,0.26 2.75,0.458 0.313,0.198 10 false M30 1.26,2.063 1.781,2.406 0.521,0.344 10 false DATA 0.219,2.063 0.74,2.406 0.521,0.344 10 false GND 0.292,0.354 0.604,0.552 0.313,0.198 10 false *a 0.729,2.313 1.042,2.51 0.313,0.198 10 false *b 0.188,3.24 0.656,3.5 0.469,0.26 10 false GND 1.01,4.156 1.323,4.354 0.313,0.198 10 false *c 2.219,4.167 2.531,4.365 0.313,0.198 10 false *d 1.854,0.385 2.177,0.583 0.323,0.198 10 false *a 0.74,0.25 1.052,0.448 0.313,0.198 10 false M23 2.01,2.031 2.531,2.375 0.521,0.344 10 false DATA 2.906,2.042 3.427,2.385 0.521,0.344 10 false GND 0.104,0.073 0.417,0.271 0.313,0.198 10 false *A 1.813,0.073 2.125,0.271 0.313,0.198 10 false *B
*A w/ Tire Pressure Warning System
*B w/o Tire Pressure Warning System
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1
*c Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*d After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check the waveform.

OK:
w/ Tire Pressure Warning System
Tester Connection Condition Tool Setting Specified Condition
M23-2 (DATA) - M23-12 (GND) Procedure:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)

w/o Tire Pressure Warning System
Tester Connection Condition Tool Setting Specified Condition
M30-5 (DATA) - M30-1 (GND) Procedure:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)


HINT:

Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).



Result:
Proceed to
OK
NG



OK

36.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DOOR CONTROL RECEIVER

36.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) and perform registration again.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

37.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
37.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally (for LHD) B
Wireless door lock function does not operate normally (for RHD) C



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)