This DTC is stored when the SSW1 contact signal and SSW2 contact signal, which are detected when the engine switch is operated, do not match.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2278 | Engine/Power Switch Malfunction | When the engine switch is operated, the SSW1 contact signal and SSW2 contact signal do not match (1-trip detection logic*). | ·
AM2 fuse ·
Engine switch ·
Certification ECU (smart key ECU assembly) ·
Wire harness or connector |
DTC Output Confirmation Operation:
Turn the engine switch on (IG). |
*: Only detected while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
| If either the SSW1 contact signal or SSW2 contact signal is stuck on, the power source mode cannot be changed by pressing the engine switch. If either the SSW1 contact signal or SSW2 contact signal is stuck off, emergency stop by pressing and holding the engine switch for 2 seconds or more cannot be operated. | - |
| DTC No. | Data List and Active Test |
|---|---|
| B2278 | Power Source Control
·
Starter Switch1 ·
Starter Switch2 |
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Inspect the fuses of circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Start Function) Precaution.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Start Switch1 | Engine switch 1 status | OFF or ON | OFF: Engine switch not pressed
ON: Engine switch pressed |
·
If the engine switch is pressed for a short time, the display may not change. ·
Use this item to determine if the engine switch input signal is malfunctioning. |
| Start Switch2 | Engine switch 2 status | OFF or ON | OFF: Engine switch not pressed
ON: Engine switch pressed |
·
Backup for engine switch 1. However, when the engine switch is pressed and held, the power source mode can only be changed when both engine switch 1 and 2 are normal. ·
Behaves the same way as engine switch 1. |
| Tester Display |
|---|
| Start Switch1 |
| Start Switch2 |
The GTS display changes correctly in response to the engine switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List while wiggling the wire harness.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Start Switch1 | Engine switch 1 status | OFF or ON | OFF: Engine switch not pressed
ON: Engine switch pressed |
·
If the engine switch is pressed for a short time, the display may not change. ·
Use this item to determine if the engine switch input signal is malfunctioning. |
| Start Switch2 | Engine switch 2 status | OFF or ON | OFF: Engine switch not pressed
ON: Engine switch pressed |
·
Backup for engine switch 1. However, when the engine switch is pressed and held, the power source mode can only be changed when both engine switch 1 and 2 are normal. ·
Behaves the same way as engine switch 1. |
| Tester Display |
|---|
| Start Switch1 |
| Start Switch2 |
The GTS display changes correctly in response to the engine switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>B2271
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>B2271
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F1 certification ECU (smart key ECU assembly) connector.
Disconnect the F59 engine switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-23 (SSW1) - F59-5 (SS1) | Always | Below 1 Ω |
| F1-21 (SSW2) - F59-1 (SS2) | Always | Below 1 Ω |
| F1-11 (AGND) - F59-6 (AGND) | Always | Below 1 Ω |
| F1-23 (SSW1) or F59-5 (SS1) - Body ground | Always | 10 kΩ or higher |
| F1-21 (SSW2) or F59-1 (SS2) - Body ground | Always | 10 kΩ or higher |
| F1-11 (AGND) or F59-6 (AGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the engine switch.
for 8NR-FTS with LHD: Click hereEngine / Hybrid System>8NR-FTS (STARTING)>ENGINE SWITCH (for LHD)>REMOVAL
for 8NR-FTS with RHD: Click hereEngine / Hybrid System>8NR-FTS (STARTING)>ENGINE SWITCH (for RHD)>REMOVAL
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE (STARTING)>ENGINE SWITCH>REMOVAL
Inspect the engine switch.
for 8NR-FTS with LHD: Click hereEngine / Hybrid System>8NR-FTS (STARTING)>ENGINE SWITCH (for LHD)>INSPECTION
for 8NR-FTS with RHD: Click hereEngine / Hybrid System>8NR-FTS (STARTING)>ENGINE SWITCH (for RHD)>INSPECTION
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE (STARTING)>ENGINE SWITCH>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 8NR-FTS with LHD) | B |
| NG (for 8NR-FTS with RHD) | C |
| NG (for 3ZR-FAE) | D |
A
B
C
D