If the remote engine start ECU does not respond to the certification ECU (smart key ECU assembly) or the remote engine start ID is not registered, this DTC is stored.
Registration status of the remote engine start ECU ID can be checked using the "Wireless C Code" item in the Data List.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2779 | Engine Starter Communication Malfunction | One of the following conditions is met (1 trip detection logic*):
·
A remote start communication error occurs. ·
Response is not possible. ·
Registration has not been performed. |
·
Remote engine start ECU ·
Main body ECU (multiplex network body ECU) ·
Certification ECU (smart key ECU assembly) |
DTC output confirmation operation:
A remote start operation is performed. |
*: Only output while a malfunction is present.
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | - | ○ | ○ | ○ |
| Malfunction Status | A remote start communication error occurs. | ○ | - | - |
| Response is not possible. | - | ○ | - | |
| Registration has not been performed. | - | - | ○ | |
| Detection Time | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine does not start with remote start operation | Engine cannot be started by remote start operation only |
| DTC No. | Data List and Active Test |
|---|---|
| B2779 | ·
Wireless Starter Com ID ·
Wireless C Code |
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.
Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.
After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
Check for CAN communication system DTCs.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
CAN communication DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wireless C Code | Registration status between remote engine starter ECU and certification ECU (smart key ECU assembly) | No Regd or Regd | No Regd: Remote starter ID not registered to remote engine start ECU and certification ECU (smart key ECU assembly)
Regd: Remote starter ID registered Remote starter ID remote engine start ECU and certification ECU (smart key ECU assembly) |
Problems may be caused by the following:
·
DTC B2779 is stored. ·
Remote engine start ECU registration has not been performed. ·
Malfunctions in the certification ECU (smart key ECU assembly) or remote engine start ECU. |
| Tester Display |
|---|
| Wireless C Code |
| Result | Proceed to |
|---|---|
| "No Regd" is displayed on the GTS | A |
| "Regd" is displayed on the GTS | B |
A
B
Register the remote engine starter ID.
| Proceed to |
|---|
| NEXT |
NEXT
Check the remote engine starter function.
Remote engine starter functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the remote engine starter ECU with a new one.
Register the remote engine starter ID.
Check the remote engine starter function.
Remote engine starter functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the main body ECU (multiplex network body ECU) with a new one.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Check the remote engine starter function.
Remote engine starter functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG