Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299016 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Power Source Circuit  


DESCRIPTION

Based on changes in the power source voltage, the main body ECU (multiplex network body ECU) can detect if the battery has been disconnected and reconnected.

WIRING DIAGRAM

E352026E02
1.49,0.865 2.396,1.052 0.906,0.188 10 false from Battery 3.521,1.656 5.135,2.083 1.615,0.427 10 false Instrument Panel Junction Block Assembly 5.177,1.927 6.823,2.354 1.646,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 3.99,1.031 5.083,1.208 1.094,0.177 10 false ECU-DCC NO. 2 5.135,0.875 5.427,1.052 0.292,0.177 10 false MB 3.531,0.885 3.823,1.063 0.292,0.177 10 false 3F 3.552,0.688 3.844,0.865 0.292,0.177 10 false 1 5.146,0.677 5.438,0.854 0.292,0.177 10 false 31 5.469,0.875 5.906,1.042 0.438,0.167 10 false BECU

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SUPPLY)
a.

Disconnect the 3F instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).


B424477C06
1.396,0.292 1.667,0.531 0.271,0.24 4.896,0.5 5.167,0.74 0.271,0.24 6.573,1.063 6.198,1.406 true 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 1.458,0.323 1.771,0.521 0.313,0.198 10 false 3F 4.927,0.531 5.24,0.729 0.313,0.198 10 false MB 5.76,1.323 6.323,1.542 0.563,0.219 10 false BECU
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3F-1 - MB-31 (BECU) Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

D

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY