The ECM stores this DTC when the communication line between the ECM and transponder key ECU assembly is malfunctioning or the communication ID of the ECM and transponder key ECU assembly do not match.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2799 | Engine Immobiliser System Malfunction | Either condition is met (1 trip detection logic*2):
·
A malfunction occurs in the communication or communication lines between the ECM and transponder key ECU assembly. ·
A communication code cannot be verified during communication between the ECM and transponder key ECU assembly. |
·
Wire harness or connector ·
Transponder key ECU assembly ·
ECM |
DTC Output Confirmation Operation:
·
Start the engine and wait 10 seconds.*1 ·
After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.*2 *1: Communication starts within 3 seconds of starting the engine. If verification fails, this DTC is stored 6 seconds after communication has completed. *2: Communication starts within 3 seconds of turning the ignition switch to ON. If verification fails, this DTC is stored 6 seconds after communication has completed. |
| B279986 | Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid | Either condition is met (1 trip detection logic*2):
·
A malfunction occurs in the communication or communication lines between the ECM and transponder key ECU assembly. ·
A communication code cannot be verified during communication between the ECM and transponder key ECU assembly. |
·
Wire harness or connector ·
Transponder key ECU assembly ·
ECM |
DTC Output Confirmation Operation:
·
Start the engine and wait 10 seconds.*1 ·
After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.*2 *1: Communication starts within 3 seconds of starting the engine. If verification fails, this DTC is stored 6 seconds after communication has completed. *2: Communication starts within 3 seconds of turning the ignition switch to ON. If verification fails, this DTC is stored 6 seconds after communication has completed. |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Engine start operation. | ○ | ○ |
| Malfunction Status | A malfunction occurs in the communication or communication lines between the ECM and transponder key ECU assembly. | ○ | - |
| A communication code cannot be verified during communication between the ECM and transponder key ECU assembly. | - | ○ | |
| Detection Time | - | - | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine cannot be started | - |
| DTC No. | Data List and Active Test |
|---|---|
·
B2799*1 ·
B279986*2 |
- |
*1: for 3ZR-FAE
*2: for 8NR-FTS
If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.
Clear the DTCs.
for 8NR-FTS:
for 3ZR-FAE:
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine.
Check for DTCs.
for 8NR-FTS:
for 3ZR-FAE:
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
B2799*1 or B279986*2 is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (DTC B2799*1 or B279986*2 is output) | B |
| NG (Other DTCs are output) | C |
*1: for 3ZR-FAE
*2: for 8NR-FTS
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Using an oscilloscope, check the waveform
| *a | Component with harness connected
(ECM) |
*b | Waveform |
| Item | Content |
|---|---|
| Tester Connection | A38-45 (IMO) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Terminal IMO stuck low (2.4 V or less)) | B |
| NG (Terminal IMO stuck high (12 V) or abnormal waveform) | C |
A
B
C
Using an oscilloscope, check the waveform
| *a | Component with harness connected
(ECM) |
*b | Waveform |
| Item | Content |
|---|---|
| Tester Connection | A38-28 (IMI) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Ignition switch ON |
Waveform is similar to that shown in the illustration.
| Result | Proceed to |
|---|---|
| OK | A |
| NG | B |
A
B
Reregister the ECU communication ID.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the ECM with a new one.
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>ECM>REMOVAL
for 8NR-FTS: Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Reregister the ECU communication ID.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A38 ECM connector
Turn the ignition switch to ON
| *a | Front view of wire harness connector
(to ECM) |
Measure the voltage according to the value(s) in the table below
| Tester Connection | Condition | Result |
|---|---|---|
| A38-45 (IMO) - Body ground | Ignition switch turned to ON using registered key | Terminal IMO stuck low (2.4 V or less) |
| Terminal IMO stuck high (12 V) or Abnormal waveform |
| Result | Proceed to |
|---|---|
| Terminal IMO stuck low (2.4 V or less) | A |
| Terminal IMO stuck high (12 V) or Abnormal waveform | B |
A
B
Disconnect the F22 transponder key ECU assembly connector
Disconnect the A38 ECM connector
Measure the resistance according to the value(s) in the table below
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F22-12 (EFII) - A38-45 (IMO) | Always | Below 1 Ω |
| A38-45 (IMO) - Body ground | Always | 10 kΩ or higher |
| F22-12 (EFII) - Body ground | Always | 10 kΩ or higher |
| F22-13 (EFIO) - A38-28 (IMI) | Always | Below 1 Ω |
| A38-28 (IMI) - Body ground | Always | 10 kΩ or higher |
| F22-13 (EFIO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the transponder key ECU assembly with a new one.
Refer to Service Bulletin.
Key ID code registration is necessary when replacing the transponder key ECU assembly.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 3ZR-FAE) | B |
| NG (for 8NR-FTS) | C |
A
B
C