Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (w/o Entry and Start System) › 2016.10–2018.05
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299017 IMMOBILISER SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

If the key ID codes of the key and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM

E329286E12
0.406,2.927 0.865,3.125 0.458,0.198 10 false F22 0.406,3.094 1.833,3.51 1.427,0.417 10 false Transponder Key ECU Assembly 5.875,2.938 6.333,3.135 0.458,0.198 10 false A38 5.875,3.094 6.333,3.292 0.458,0.198 10 false ECM 5.323,1.906 5.781,2.104 0.458,0.198 10 false IMI 5.323,1 5.781,1.198 0.458,0.198 10 false IMO 5.49,1.563 5.885,1.813 0.396,0.25 10 false 12 V 1.188,0.354 1.583,0.604 0.396,0.25 10 false 12 V 1.573,0.99 2.188,1.188 0.615,0.198 10 false EFII 1.531,1.906 2.146,2.104 0.615,0.198 10 false EFIO 1.979,0.99 2.344,1.208 0.365,0.219 10 false 12 1.979,1.906 2.219,2.115 0.24,0.208 10 false 13 5.031,1.01 5.344,1.208 0.313,0.198 10 false 45 5.021,1.906 5.333,2.104 0.313,0.198 10 false 28

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

i.

for 8NR-FTS:

Powertrain > Engine > Clear DTCs
50002 372

ii.

for 3ZR-FAE:

Powertrain > Engine and ECT > Clear DTCs
50002 234


Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Immobiliser > Trouble Codes
50001 260
i.

for 8NR-FTS:

Powertrain > Engine > Trouble Codes
50001 372

ii.

for 3ZR-FAE:

Powertrain > Engine and ECT > Trouble Codes
50001 234


OK:

DTC is not output.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Engine / Active Test.


e.

Perform the Active Test according to the display on the GTS.

i.

for 8NR-FTS:

Powertrain > Engine
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status Status of immobiliser system fuel cut OFF/ON - -
Powertrain > Engine > Data List
Tester Display
Immobiliser Fuel Cut Status
50003 372 65

ii.

for 3ZR-FAE:

Powertrain > Engine and ECT
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut OFF/ON - -
Powertrain > Engine and ECT > Data List
Tester Display
Immobiliser Fuel Cut
50003 234 505


OK:

OFF is displayed after the engine is started.


Result:
Result Proceed to
OK (for 3ZR-FAE) A
OK (for 8NR-FTS) B
NG C



A

B

C

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

B

5.CHECK ECM (TERMINAL IMI)
5.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform

B319576C33
5.396,0.396 5.76,0.656 0.365,0.26 5.125,2.042 5.125,1.208 true 0.313,0.406 0.625,0.604 0.313,0.198 10 false *a 1.01,4.042 1.427,4.302 0.417,0.26 10 false GND 3.333,4.125 3.75,4.385 0.417,0.26 10 false *b 5.052,2.083 5.469,2.344 0.417,0.26 10 false IMI 5.458,0.448 5.875,0.708 0.417,0.26 10 false A38
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection A38-28 (IMI) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch ON


Result:
Result Proceed to
Normal waveform A
Waveform not output, or has abnormal wavelength or shape B



A

6.CHECK ECM (TERMINAL IMO)

B

11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
6.CHECK ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform

B319577C60
5.417,0.385 5.833,0.667 0.417,0.281 5.167,2 4.917,1.313 true 0.292,0.385 0.604,0.583 0.313,0.198 10 false *a 1.01,4.042 1.396,4.292 0.385,0.25 10 false GND 2.938,4.094 3.323,4.344 0.385,0.25 10 false *b 5.51,0.458 5.896,0.708 0.385,0.25 10 false A38 5.094,2.042 5.479,2.292 0.385,0.25 10 false IMO
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection A38-45 (IMO) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of the ignition switch first being turned to ON after cable is disconnected and reconnected to the negative (-) battery terminal


Result:
Result Proceed to
Normal waveform A
Waveform not output, or has abnormal wavelength or shape (for 3ZR-FAE) B
Waveform not output, or has abnormal wavelength or shape (for 8NR-FTS) C



A

7.REGISTER ECU COMMUNICATION ID

B

C

7.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID between the transponder key ECU assembly and ECM.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

B

9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER ENGINE STARTS
10.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG (for 3ZR-FAE) B
NG (for 8NR-FTS) C



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

C

11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the F22 transponder key ECU assembly connector


b.

Disconnect the A38 ECM connector


c.

Measure the resistance according to the value(s) in the table below

Standard Resistance:
Tester Connection Condition Specified Condition
F22-13 (EFIO) - A38-28 (IMI) Always Below 1 Ω
F22-13 (EFIO) - Body ground Always 10 kΩ or higher
A38-28 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR