Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (w/o Entry and Start System) › 2016.10–2018.05
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299017 IMMOBILISER SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

The transponder key ECU assembly blinks the security indicator light when the immobiliser is set.

WIRING DIAGRAM

E360664E01
5.417,3.115 7.125,3.479 1.708,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 5.417,1.323 6.896,1.677 1.479,0.354 10 false Transponder Key ECU Assembly 5.417,1.135 5.875,1.333 0.458,0.198 10 false F22 5.427,2.969 5.885,3.167 0.458,0.198 10 false F15 5.781,2.521 6.24,2.719 0.458,0.198 10 false IND 5.74,0.719 6.198,0.917 0.458,0.198 10 false IND 5.531,0.719 5.688,0.917 0.156,0.198 10 false 8 5.51,2.51 5.823,2.708 0.313,0.198 10 false 15 1.021,1.313 1.479,1.51 0.458,0.198 10 false F81 1.021,1.5 2.583,1.896 1.563,0.396 10 false Security Indicator Light (Clock Assembly) 2.094,0.854 2.406,1.052 0.313,0.198 10 false LP 2.396,0.729 2.552,0.927 0.156,0.198 10 false 9 1.354,0.844 1.51,1.042 0.156,0.198 10 false E 1.188,0.708 1.344,0.906 0.156,0.198 10 false 5 4.344,1.729 4.656,1.927 0.313,0.198 10 false *1 0.427,3.281 2.417,3.479 1.99,0.198 10 false *1: w/ Theft Deterrent System 6.375,0.271 6.833,0.469 0.458,0.198 10 false 12V 6.417,2.052 6.875,2.25 0.458,0.198 10 false 12V

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly is replaced, refer to Service Bulletin.


PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specification.

Result:
Result Proceed to
w/o Theft Deterrent System A
w/ Theft Deterrent System B




A

2.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)

B

5.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
2.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Immobiliser / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
OK:

Security indicator light can be turned on and off using the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - SECURITY INDICATOR LIGHT AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - SECURITY INDICATOR LIGHT AND BODY GROUND)
a.

Disconnect F22 transponder key ECU assembly connector.


b.

Disconnect the F81 security indicator light connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-9 (LP) - F22-8 (IND) Always Below 1 Ω
F81-9 (LP) - Body ground Always 10 kΩ or higher
F22-8 (IND) - Body ground Always 10 kΩ or higher
F81-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)
a.

Connect the F22 transponder key ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F81-9 (LP) - Body ground Key not in ignition key cylinder Pulse generation
Key in ignition key cylinder Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

5.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Immobiliser or Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF -
Body Electrical > Main Body > Active Test
Tester Display
Security Indicator
50004 123 19

Result:
Result Proceed to
Security indicator light operation is normal when performing the "Main Body" and "Immobiliser" Active Test A
·

Security indicator light operation is not normal when performing the "Immobiliser" Active Test

·

Security indicator light operation is normal when performing the "Main Body" Active Test


B
·

Security indicator light operation is normal when performing the "Immobiliser" Active Test

·

Security indicator light operation is not normal when performing the "Main Body" Active Test


C
Security indicator light operation is not normal when performing the "Main Body" and "Immobiliser" Active Test D



A

6.CHECK SECURITY INDICATOR LIGHT OPERATION

B

7.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - TRANSPONDER KEY ECU ASSEMBLY)

C

8.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - MAIN BODY ECU)

D

9.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - MAIN BODY ECU OR TRANSPONDER KEY ECU)
6.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

When the immobiliser is set, check that the security indicator light blinks.*1

OK:

The security indicator light blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light is on.*2

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION

OK:

The security indicator light is on.



Result:
Result Proceed to
Both *1 and *2 are OK A
*1 is NG (*2 is OK) B
*2 is NG (*1 is OK) (for LHD) C
*2 is NG (*1 is OK) (for RHD) D
Both *1 and *2 are NG E



A

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

D

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

E

REPLACE SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the F81 security indicator light connector.


b.

Disconnect the F22 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F22-8 (IND) - F81-9 (LP) Always Below 1 Ω
F22-8 (IND) - Body ground Always 10 kΩ or higher
F81-9 (LP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - MAIN BODY ECU)
a.

Disconnect the F81 security indicator light connector.


b.

Disconnect the F15 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F15-15 (IND) - F81-9 (LP) Always Below 1 Ω
F15-15 (IND) - Body ground Always 10 kΩ or higher
F81-9 (LP) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - MAIN BODY ECU OR TRANSPONDER KEY ECU)
a.

Disconnect the F81 security indicator light connector.


b.

Disconnect F22 transponder key ECU assembly connector.


c.

Disconnect the F15 main body ECU (multiplex network body ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except Sedan
Tester Connection Condition Specified Condition
F22-8 (IND) - F81-9 (LP) Always Below 1 Ω
F15-15 (IND) - F81-9 (LP) Always Below 1 Ω
F22-8 (IND) - Body ground Always 10 kΩ or higher
F81-9 (LP) - Body ground Always 10 kΩ or higher
F81-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.REPLACE SECURITY INDICATOR LIGHT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE SECURITY INDICATOR LIGHT
a.

Temporarily replace the security indicator light (clock assembly) with a new or known good one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>CLOCK>REMOVAL


b.

When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.

OK:

Security indicator light blinks.



Result:
Proceed to
OK
NG



OK

END (SECURITY INDICATOR LIGHT WAS DEFECTIVE)

NG

11.REPLACE TRANSPONDER KEY ECU ASSEMBLY
11.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new or known good one.

HINT:

Refer to Service Bulletin.



b.

When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.

OK:

Security indicator light blinks.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)