Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM32H0E _57 Power Source / Network _059621 NETWORKING _0299023 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1206  P/W Master Switch Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the multiplex network master switch assembly and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1206 P/W Master Switch Communication Stop No communication between multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Multiplex network master switch assembly

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

ECU-B NO. 2 fuse



WIRING DIAGRAM

B457237E05
0.969,0.719 1.583,0.917 0.615,0.198 10 false LIN2 0.104,1.74 0.604,1.99 0.5,0.25 10 false MB 0.104,1.906 1.802,2.375 1.698,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 1.365,1.073 1.979,1.271 0.615,0.198 10 false 3H 1.365,1.229 2.99,1.656 1.625,0.427 10 false Instrument Panel Junction Block Assembly 1.396,0.531 1.615,0.719 0.219,0.188 10 false 16 2.99,0.531 3.26,0.719 0.271,0.188 10 false 25 3.5,0.531 3.771,0.719 0.271,0.188 10 false 17 3.802,0.719 4.417,0.917 0.615,0.198 10 false LIN1 4.427,0.563 5.042,0.76 0.615,0.198 10 false B 4.229,1.281 4.844,1.479 0.615,0.198 10 false GND 4.677,0.469 4.948,0.656 0.271,0.188 10 false 11 4.677,1.188 4.948,1.375 0.271,0.188 10 false 12 4.656,0.708 6.104,0.927 1.448,0.219 10 false ECU-B NO. 2 5.677,0.563 7.125,0.781 1.448,0.219 10 false from Battery 3.333,1.917 4.948,2.344 1.615,0.427 10 false Multiplex Network Master Switch Assembly 3.333,1.719 4.333,1.927 1,0.208 10 false J6*1, I6*2 0.917,3.083 2.823,3.333 1.906,0.25 10 false : LIN Communication Line 5.219,2.531 6.667,2.75 1.448,0.219 10 false *1: for LHD 5.219,2.948 6.667,3.167 1.448,0.219 10 false *2: for RHD


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*1


*1: w/ Entry and Start System



PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


B426689C10
2.083,1 2.417,1.25 0.333,0.25 5.5,0.75 5.833,1 0.333,0.25 2.198,2.156 2.198,1.573 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 2.156,1.052 2.469,1.25 0.313,0.198 10 false MB 5.583,0.802 5.896,1 0.313,0.198 10 false 3H 2.083,2.219 2.698,2.417 0.615,0.198 10 false LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
3H-25 - MB-16 (LIN2) Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

for LHD

i.

Disconnect the J6 multiplex network master switch assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
3H-25 - J6-17 (LIN1) Ignition switch off Below 1 Ω
J6-17 (LIN1) or 3H-25 - Body ground Ignition switch off 10 kΩ or higher




b.

for RHD

i.

Disconnect the I6 multiplex network master switch assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
3H-25 - I6-17 (LIN1) Ignition switch off Below 1 Ω
I6-17 (LIN1) or 3H-25 - Body ground Ignition switch off 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - BATTERY, BODY GROUND)
a.

for LHD

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J6-11 (B) - J6-12 (GND) Always 11 to 14 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J6-12 (GND) - Body ground Always Below 1 Ω




b.

for RHD

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I6-11 (B) - I6-12 (GND) Always 11 to 14 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I6-12 (GND) - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

4.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Replace the multiplex network master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B1206 is not output.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)