If the main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 7 seconds or more, DTC B2325 will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2325 | LIN Communication Bus Malfunction | The main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 7 seconds or more. | ·
Power window regulator motor assembly (for driver door) ·
Power window regulator motor assembly (for front passenger door) ·
Power window regulator motor assembly (for rear RH door) ·
Power window regulator motor assembly (for rear LH door) ·
Multiplex network master switch assembly ·
Double lock door control relay assembly*1 ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly ·
Wire harness or connector ·
ECU-B NO. 2 fuse ·
POWER fuse ·
DOOR fuse ·
DOOR R/L fuse ·
DOOR R/R fuse ·
DOOR DBL/L fuse*1 ·
ECU-DCC NO. 2 fuse*1 |
*1: w/ Double Locking System
Inspect the fuses for circuits related to this system before performing the following procedure.
When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION
Before performing the inspection, check that DTC B1206, B1249, B2321, B2322, B2323 or B2324 is not output.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*1
*1: w/ Entry and Start System
Remove the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3H-25 - MB-16 (LIN2) | Always | Below 1 Ω |
| 3D-17 - MB-16 (LIN2) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
for LHD
Disconnect the J2 power window regulator motor assembly (for driver door) connector.
Disconnect the I2 power window regulator motor assembly (for front passenger door) connector.
Disconnect the L2 power window regulator motor assembly (for rear LH door) connector.
Disconnect the K2 power window regulator motor assembly (for rear RH door) connector.
Disconnect the J6 multiplex network master switch assembly connector.
Disconnect the F14 double lock door control relay assembly connector.*1
Measure the resistance according to the value(s) in the table below.
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3H-25 - J6-17 (LIN1) | Ignition switch off | Below 1 Ω |
| 3D-17 - F14-9 (LIN)*1 | Ignition switch off | Below 1 Ω |
| 3H-25 - I2-9 (LIN) | Ignition switch off | Below 1 Ω |
| 3H-25 - L2-9 (LIN) | Ignition switch off | Below 1 Ω |
| 3H-25 - K2-9 (LIN) | Ignition switch off | Below 1 Ω |
| 3H-25 - J2-9 (LIN) | Ignition switch off | Below 1 Ω |
| J6-17 (LIN1) - Body ground | Ignition switch off | 10 kΩ or higher |
| F14-9 (LIN) - Body ground*1 | Ignition switch off | 10 kΩ or higher |
| 3H-25 or 3D-17 - Body ground | Ignition switch off | 10 kΩ or higher |
| I2-9 (LIN) - Body ground | Ignition switch off | 10 kΩ or higher |
| L2-9 (LIN) - Body ground | Ignition switch off | 10 kΩ or higher |
| K2-9 (LIN) - Body ground | Ignition switch off | 10 kΩ or higher |
| J2-9 (LIN) - Body ground | Ignition switch off | 10 kΩ or higher |
*1: w/ Double Locking System
for RHD
Disconnect the I2 power window regulator motor assembly (for driver door) connector.
Disconnect the J2 power window regulator motor assembly (for front passenger door) connector.
Disconnect the L2 power window regulator motor assembly (for rear LH door) connector.
Disconnect the K2 power window regulator motor assembly (for rear RH door) connector.
Disconnect the I6 multiplex network master switch assembly connector.
Disconnect the F14 double lock door control relay assembly connector.*1
Measure the resistance according to the value(s) in the table below.
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3H-25 - I6-17 (LIN1) | Ignition switch off | Below 1 Ω |
| 3D-17 - F14-9 (LIN)*1 | Ignition switch off | Below 1 Ω |
| 3H-25 - I2-9 (LIN) | Ignition switch off | Below 1 Ω |
| 3H-25 - L2-9 (LIN) | Ignition switch off | Below 1 Ω |
| 3H-25 - K2-9 (LIN) | Ignition switch off | Below 1 Ω |
| 3H-25 - J2-9 (LIN) | Ignition switch off | Below 1 Ω |
| I6-17 (LIN1) - Body ground | Ignition switch off | 10 kΩ or higher |
| F14-9 (LIN) - Body ground*1 | Ignition switch off | 10 kΩ or higher |
| 3H-25 or 3D-17 - Body ground | Ignition switch off | 10 kΩ or higher |
| I2-9 (LIN) - Body ground | Ignition switch off | 10 kΩ or higher |
| L2-9 (LIN) - Body ground | Ignition switch off | 10 kΩ or higher |
| K2-9 (LIN) - Body ground | Ignition switch off | 10 kΩ or higher |
| J2-9 (LIN) - Body ground | Ignition switch off | 10 kΩ or higher |
*1: w/ Double Locking System
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Reconnect the 3D and 3H instrument panel junction block assembly connectors.
Reconnect the J2 power window regulator motor assembly (for driver door) connector.
Reconnect the I2 power window regulator motor assembly (for front passenger door) connector.
Reconnect the K2 power window regulator motor assembly (for rear RH door) connector.
Reconnect the J6 multiplex network master switch assembly connector.
Reconnect the F14 double lock door control relay assembly connector.*1
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
After 10 seconds have elapsed, check if the same DTC is output again.
*1: w/ Double Locking System
for RHD
Reconnect the 3D and 3H instrument panel junction block assembly connectors.
Reconnect the I2 power window regulator motor assembly (for driver door) connector.
Reconnect the J2 power window regulator motor assembly (for front passenger door) connector.
Reconnect the K2 power window regulator motor assembly (for rear RH door) connector.
Reconnect the I6 multiplex network master switch assembly connector.
Reconnect the F14 double lock door control relay assembly connector.*1
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
After 10 seconds have elapsed, check if the same DTC is output again.
*1: w/ Double Locking System
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
for LHD
Reconnect the L2 power window regulator motor assembly (for rear LH door) connector.
Disconnect the J6 multiplex network master switch assembly connector.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
After 10 seconds have elapsed, check if the same DTC is output again.
for RHD
Reconnect the L2 power window regulator motor assembly (for rear LH door) connector.
Disconnect the I6 multiplex network master switch assembly connector.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
After 10 seconds have elapsed, check if the same DTC is output again.
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
for LHD
Reconnect the J6 multiplex network master switch assembly connector.
Disconnect the K2 power window regulator motor assembly (for rear RH door) connector.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
After 10 seconds have elapsed, check if the same DTC is output again.
for RHD
Reconnect the I6 multiplex network master switch assembly connector.
Disconnect the K2 power window regulator motor assembly (for rear RH door) connector.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
After 10 seconds have elapsed, check if the same DTC is output again.
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
for LHD
Reconnect the K2 power window regulator motor assembly (for rear RH door) connector.
Disconnect the J2 power window regulator motor assembly (for driver door) connector.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
After 10 seconds have elapsed, check if the same DTC is output again.
for RHD
Reconnect the K2 power window regulator motor assembly (for rear RH door) connector.
Disconnect the I2 power window regulator motor assembly (for driver door) connector.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
After 10 seconds have elapsed, check if the same DTC is output again.
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
for LHD
Reconnect the J2 power window regulator motor assembly (for driver door) connector.
Disconnect the I2 power window regulator motor assembly (for front passenger door) connector.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
After 10 seconds have elapsed, check if the same DTC is output again.
for RHD
Reconnect the I2 power window regulator motor assembly (for driver door) connector.
Disconnect the J2 power window regulator motor assembly (for front passenger door) connector.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
After 10 seconds have elapsed, check if the same DTC is output again.
| Result | Proceed to |
|---|---|
| DTC B2325 is output (w/ Double Locking System) | A |
| DTC B2325 is output (w/o Double Locking System) (for LHD) | B |
| DTC B2325 is output (w/o Double Locking System) (for RHD) | C |
| DTC B2325 is not output | D |
A
B
C
D
Reconnect each ECU connector.
Disconnect the F14 double lock door control relay assembly connector.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
After 10 seconds have elapsed, check if the same DTC is output again.
| Result | Proceed to |
|---|---|
| DTC B2325 is output (for LHD) | A |
| DTC B2325 is output (for RHD) | B |
| DTC B2325 is not output | C |
A
B
C