This DTC is stored when the headlight ECU sub-assembly LH detects a malfunction in the rear height control sensor sub-assembly LH power source circuit or rear height control sensor sub-assembly LH circuit. The headlight ECU sub-assembly LH stores DTC B2416 and/or B241A.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2416 | Height Control Sensor Malfunction | Any of the following conditions is met:
·
Malfunction in rear height control sensor sub-assembly LH ·
Open in rear height control sensor sub-assembly LH power source circuit ·
Short in rear height control sensor sub-assembly LH power source circuit |
·
Rear height control sensor sub-assembly LH ·
Headlight ECU sub-assembly LH ·
Harness or connector |
- |
| B241A | Rear Height Control Sensor | Any of the following conditions is met:
·
Malfunction in rear height control sensor sub-assembly LH ·
Open in rear height control sensor sub-assembly LH circuit ·
Short in rear height control sensor sub-assembly LH circuit |
·
Rear height control sensor sub-assembly LH ·
Headlight ECU sub-assembly LH ·
Harness or connector |
- |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ |
| Malfunction Status | Malfunction in rear height control sensor sub-assembly LH | ○ | - | - |
| Open in rear height control sensor sub-assembly LH power source circuit | - | ○ | - | |
| Short in rear height control sensor sub-assembly LH power source circuit | - | - | ○ | |
| Detection Time | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
Before performing this inspection, check that the rear height control sensor sub-assembly LH is installed correctly.
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION
If any of the following are performed, it is necessary to initialize the headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION
Replacement of the rear height control sensor sub-assembly LH
Removal/installation of the rear height control sensor sub-assembly LH
Work that changes the vehicle height such as replacement of suspension components
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON.
Check for DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>DTC CHECK / CLEAR
DTC B2416 or B241A are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Height Sens Pw Supply Val | Rear height control sensor sub-assembly LH power supply value | 0 to 5.00 V | 4.61 to 5.00 V | - |
| Rr Height Sens Signal Val | Rear height control sensor sub-assembly LH signal value | 0 to 5.00 V | 0.50 to 4.50 V | Value changes according to vehicle height |
| Tester Display |
|---|
| Height Sens Pw Supply Val |
| Rr Height Sens Signal Val |
Normal condition listed above is displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A16 headlight ECU sub-assembly LH connector.
Disconnect the O2 rear height control sensor sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A16-16 (SBR) - O2-3 (SHB) | Always | Below 1 Ω |
| A16-17 (SHRL) - O2-2 (SHRR) | Always | Below 1 Ω |
| A16-15 (SGR) - O2-1 (SHG) | Always | Below 1 Ω |
| A16-16 (SBR) or O2-3 (SHB) - Body ground | Always | 10 kΩ or higher |
| A16-17 (SHRL) or O2-2 (SHRR) - Body ground | Always | 10 kΩ or higher |
| A16-15 (SGR) or O2-1 (SHG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear height control sensor sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL
Inspect the rear height control sensor sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>INSPECTION
Rear height control sensor sub-assembly LH is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG