Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for DENSO Made) › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0299517 AIR CONDITIONING UNIT(for DENSO Made) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for DENSO Made)  INSTALLATION  


PROCEDURE

Hide 55990B 1.INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY

a.
I112349

Engage the claws to install the lower defroster nozzle assembly.


Hide 2.TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

Temporarily install the air conditioner unit assembly to the instrument panel reinforcement assembly with the 3 bolts.


Hide 3.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:

Be sure to support the air conditioner unit assembly when installing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.


a.

Engage the guides to install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.

I112491C01
0,0 0,0 false
V113147

Install in this Direction - -



b.
I112356

Connect the 2 connectors.


c.

Engage the clamps.


d.

Install the 5 bolts.

I113811N01
1.052,3.844 1.208,4.042 0.156,0.198 10 true A 1.073,2.927 1.229,3.125 0.156,0.198 10 true A 6.74,1.448 6.896,1.646 0.156,0.198 10 true A 6.729,2.292 6.885,2.49 0.156,0.198 10 true A 1.042,2.417 1.198,2.615 0.156,0.198 10 true B

Torque:
Bolt A : 25 N*m (255 kgf*cm, 18 ft.*lbf)
Bolt B : 23.6 N*m (241 kgf*cm, 17 ft.*lbf)


e.

Temporarily install the nut.


f.

Install the 2 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 88539J 4.CONNECT DRAIN COOLER HOSE

a.
I113742C03
0.958,3.208 0.688,3.01 true 0.969,3.188 1.188,3.354 0.219,0.167 10 true *1
*a Cooler Unit Drain Hose Grommet


Connect the drain cooler hose.

NOTICE:

If the cooler unit drain hose grommet is disconnected from the vehicle body while connecting the drain cooler hose, make sure to replace it with a new one. Failure to do so may cause water ingress.



Hide 82141 5.INSTALL INSTRUMENT PANEL WIRE

a.

Engage clamps and hook to connect the instrument panel wire.

I113760C02
3.417,5.25 2.677,4.583 true 3.281,4.406 3.979,4.865 3.979,4.865 3.917,4.406 true 6.542,5.031 6.729,4.646 6.729,4.646 6.573,4.375 true 2.896,5.313 3.417,5.25 3.417,5.25 2.542,3.99 true 6.302,5.49 5.906,5.375 true 1.01,4.802 0.781,4.906 true 0.917,5.552 0.719,5.469 true 1.521,0.438 1.271,0.5 true 1.073,1.229 0.813,1 true 3.396,1.052 3.917,1.25 3.917,1.25 4.198,0.979 true 2.708,1.135 2.938,1.313 true 6.396,0.906 6.625,1.083 true 0.552,2.719 1.052,3 1.052,3 0.979,2.406 true 6.781,4.552 6.99,4.76 0.208,0.208 10 true *a 5.708,5.281 5.917,5.49 0.208,0.208 10 true *a 3.479,5.208 3.688,5.417 0.208,0.208 10 true *a 3.917,4.906 4.125,5.115 0.208,0.208 10 true *a 1.021,4.688 1.229,4.896 0.208,0.208 10 true *a 1.021,1.188 1.229,1.396 0.208,0.208 10 true *a 1.063,0.427 1.271,0.635 0.208,0.208 10 true *a 2.938,1.26 3.146,1.469 0.208,0.208 10 true *a 3.823,1.26 4.031,1.469 0.208,0.208 10 true *a 6.219,0.75 6.427,0.958 0.208,0.208 10 true *a 0.938,5.51 1.146,5.719 0.208,0.208 10 true *b 1.01,3.031 1.219,3.24 0.208,0.208 10 true *a 5.708,4.094 5.896,4.292 0.188,0.198 10 true A 5.688,4.365 5.844,4.542 0.156,0.177 10 true A 6.802,5.25 6.958,5.427 0.156,0.177 10 true B 5.677,0.698 5.833,0.875 0.156,0.177 10 true C 5.635,0.344 5.792,0.521 0.156,0.177 10 true C 1.906,0.469 2.063,0.646 0.156,0.177 10 true C
*a Clamp *b Hook



b.

Install the instrument panel junction block assembly with main body ECU with the bolt and nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Install the 2 nuts A.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


d.

Install the 4 ground wires with the 4 bolts.

Torque:
Bolt B (Part No. 90119-06995) : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)
Bolt B (Part No. 90119-W0017) : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
Bolt C : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)


e.

Install the bolt and screw.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


f.

Connect each connector.


Hide 55308B 6.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.
I112457

Install the No. 3 instrument panel to cowl brace sub-assembly with the nut and bolt.

Torque:
Bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Nut : 6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Engage the clamp and claws.


Hide 55306A 7.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



c.
I113738

Engage the clamps to connect the wire harness.


Hide 55307C 8.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
I112455

Install the No. 2 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



c.
I113736

Install the ground wire with the bolt.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


d.

Engage the clamps to connect the wire harness.


e.

Install the relay block assembly with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 9.INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

Tighten the 3 bolts, 2 screws and nut in the order shown in the illustration to install the air conditioner unit .

I112492E01
1.927,0.969 2.083,1.167 0.156,0.198 10 true 2 3.75,0.896 3.906,1.094 0.156,0.198 10 true 1 5.667,0.854 5.823,1.052 0.156,0.198 10 true 3 1.125,4.438 1.281,4.635 0.156,0.198 10 true 6 3.865,4.344 4.021,4.542 0.156,0.198 10 true 5 5.01,4.344 5.167,4.542 0.156,0.198 10 true 4

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 55215D 10.INSTALL NO. 3 DASH PANEL INSULATOR PAD

a.
I112343

Engage the clips to install the No. 3 dash panel insulator pad.


b.
I112566C01
0,0 0,0 false
V113147

Install in this Direction


Install the front floor carpet assembly to its original position as shown in the illustration.


c.

Engage the clamps.


d.

Install the clip.


e.

Install the 2 front floor carpet clips.


Hide 88625Q 11.INSTALL COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)

a.

Connect the aspirator and connector to install the cooler thermistor (room temperature sensor).


Hide 82878 12.INSTALL ECU INTEGRATION BOX LH

Hide 89340A 13.INSTALL CLEARANCE WARNING ECU ASSEMBLY (w/ Clearance Sonar System)

Hide 85940 14.INSTALL WINDSHIELD WIPER RELAY ASSEMBLY

Hide 15.INSTALL STEERING COLUMN ASSEMBLY

Hide 55401E 16.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 17.INSTALL FRONT SEAT ASSEMBLY LH

Hide 18.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 88716A 19.CONNECT COOLER REFRIGERANT LIQUID PIPE A

a.

Remove the vinyl tape from the cooler refrigerant liquid pipe A.


b.

Apply sufficient compressor oil to a new O-ring and fitting surface of the cooler refrigerant liquid pipe A.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the cooler refrigerant liquid pipe A.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the cooler refrigerant liquid pipe A.


Hide 88707 20.CONNECT SUCTION PIPE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction pipe sub-assembly.


b.

Apply sufficient compressor oil to a new O-ring and fitting surface of the suction pipe sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the suction pipe sub-assembly.


e.
I112493

Rotate the hook connector as shown in the illustration.


f.

Insert the hose joint into the fitting hole securely and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87245 21.CONNECT INLET HEATER WATER HOSE

a.
I112494C01
1.656,2.927 1.177,2.792 true 0.156,2.313 0.469,2.51 0.313,0.198 10 false *a 0.969,2.677 1.281,2.875 0.313,0.198 10 false *b 2.229,2.51 2.542,2.708 0.313,0.198 10 false *c 1.125,1.26 1.313,1.469 0.188,0.208 10 true A
*a View A
*b Marking (White)
*c Clip Installation Angle (120°)


Connect the inlet heater water hose with the marking (pink) facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the inlet heater water hose.



Hide 87246 22.CONNECT OUTLET HEATER WATER HOSE

a.
I112495C01
1.771,2.927 2.219,2.854 true 0.156,2.25 0.469,2.448 0.313,0.198 10 false *a 1.021,2.417 1.333,2.615 0.313,0.198 10 false *c 2.281,2.698 2.594,2.896 0.313,0.198 10 false *b 0.938,0.938 1.115,1.135 0.177,0.198 10 true A
*a View A
*b Marking (White)
*c Clip Installation Angle (120°)


Connect the outlet heater water hose with the marking (white) facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the outlet heater water hose.



Hide 55701J 23.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55735C 24.INSTALL COWL BODY MOUNTING REINFORCEMENT RH

Hide 55736D 25.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735A 26.INSTALL WATER GUARD PLATE LH

Hide 55737B 27.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 28.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 31. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT